Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
• Do not install or store the dryer where it will be exposed to the weather. A thermal limiter switch automatically turns off the motor in the unlikely event of an overheated situation (electric dryers only). A service technician must replace the thermal limiter switch after correcting the fault. Failure to comply with these warnings could result in serious personal injuries. SAVE THESE INSTRUCTIONS 3 • Follow the guidelines below for preparing the load for drying. Drying Procedures • Read the Operating Instructions card for operating your specific model. • Always read and follow fabric care labels and laundry product labels. To reduce the risk of fire, electrical shock, or injury to persons, read Important Safety Instructions, pages 2-3, before operating this dryer. 1. Prepare items for drying. • Dry items of similar fabric, weight and construction in the same load. • Separate dark items from light-colored items. Separate items that shed lint from those that attract lint. If an item sheds lint, turn it inside out. • Be sure buckles, buttons and trim are heatproof and won't damage the drum finish. Close zippers, fasten hooks and Velcro®-like fasteners. Tie strings and sashes to prevent snagging and tangling. • If possible, turn pockets inside out for even drying. • Check for stains which may not have been removed in washing. Dryer heat may permanently set some stains. Repeat stain removal process before drying. Place small items in a mesh bag. • Place small items in a mesh bag to prevent tangling and for easy removal. 2. Check that lint screen is clean and in place. 3. Load the dryer. • The average load will fill the drum 1/3 to 1/2 full. Items need room to tumble freely for even drying and less wrinkling. Do not overload dryer. • When drying large items, dry only 2 or 3 at a time. Fill out the load with small and medium sized items. • For delicate or very small loads, add 2 lint-free towels for better drying, less wrinkling, and to prevent grease stains caused by fabric softener sheets. • Do not overdry items. Overdrying can cause wrinkling, shrinkage, harshness, and a build-up of static electricity, which can produce more lint. • If desired, add a dryer fabric softener sheet. Close the dryer door and set dryer controls (some models). See Operating Instructions card for your specific model controls. Turn cycle selector clockwise to the desired setting. Start the dryer. • Turn the START knob clockwise to ON. Hold for 1-2 seconds and release. • To add or remove items when the dryer is running, open the door. The dryer will always stop when the door is opened. Allow the drum to come to a complete stop before reaching inside. • To restart dryer, close the door then turn the START knob clockwise to ON. Hold for 1-2 seconds and release. When the cycle ends, remove items immediately and hang or fold. If load is removed before the cycle ends, turn cycle selector to OFF. Follow fabric care label instructions. 4. 7. Fill dryer drum 1/3 to 1/2 full. 4 Features Cycle Signal Control (some models) When the Cycle Signal Control is ON, a signal will sound at the end of each cycle and during the Press Saver setting (some models). The volume is adjustable on some models. Drum Light (some models) A drum light will come on whenever the door is opened to illuminate the dryer drum during loading and unloading. Closing the door turns off the light. Reversible Dryer Door Your dryer is equipped with a reversible door. The door can be hinged on the right or left side. Refer to the INSTALLATION INSTRUCTIONS for directions on changing Use the drying rack to dry items which should not be tumble dried. Open the dryer door and remove the lint screen. Insert drying rack into the dryer drum. Place the front bar under the lip of the Place items to be dried on top of the rack. Weight should not exceed 10 lbs. Leave space between items, but do not let items hang over the sides or through the grids. Do not tumble other items when using the drying rack. Select a timed dry setting best suited for items being dried. Use only the Air Fluff (no heat) temperature setting for items containing plastic, foam rubber, rubber-like materials, feathers or down. When items are dry, remove the rack and replace the lint screen. If lint screen is not in place, tumbling items could enter the exhaust system and cause Place the front bar under the lip of the lint screen opening. the door. Drying Rack (some models) lint screen opening. 4. 5. damage to the dryer. Common Drying Problems Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association. PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES Greasy, oily • Fabric softener sheet. • Rub fabric softener stains with bar soap. • Add a few bath towels to small loads for stains Rinse and rewash. proper tumbling. • Some "silk-like" fabrics should ...