Votos - , Puntuación media: ( )

Manual de usuario Hotpoint, modelo 473

Fabricar: Hotpoint
Tamaño del archivo: 528.99 kb
Nombre del archivo:

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

On some models the signal sound level cannot be adjusted. If you selected the PRESS GUARD option the signal will sound at the end of the drying time and will sound several times during the PRESS GUARD cycle. This will remind you that it is time to remove the clothes. NOTE: ¦ Remove garments promptly at the sound of the signal. Place clothes on hangers so wrinkles won’t set in. ¦ Use the Cycle Signal especially when drying fabrics like polyester knits and permanent press. These fabrics should be removed so wrinkles won’t set in. Drum Lamp—On some models Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker. Reach above dryer opening from inside the drum. Remove the bulb and replace with the same size bulb. Drying Rack—On some models A handy drying rack may be used for drying NOTE: articles such as stuffed toys, pillows or ¦ The drying rack must be used with the washable sweaters. TIMED CYCLE. Hook the rack over the lint filter so the rack ¦ Do not use this drying rack when there extends into the dryer drum. are other clothes in the dryer. 8 About reversing the door. Reversing the Door Tools needed: n Standard #2 n Tape-tipped Phillips screwdriver putty knife n Needle-nosed pliers 1 2 3 4 Open the door and remove the filler plugs opposite the hinges. With the door completely open, remove the bottom screw from each hinge on the dryer face. Insert these screws about half way into the TOP holes, for each hinge, on the opposite side (where you removed the filler plugs). Apply firm pressure to get the screw started in untapped holes. Loosen top screw from each hinge on the dryer face half way. With one hand holding the top of the door and the other hand holding the bottom, remove the door from the dryer by lifting it UP and OUT. Rotate the door 180°. Insert it on the opposite side of the opening by moving the door IN and DOWN until the top hinge and the bottom hinge are resting on the top screws inserted in step 1. Remove the remaining screws from the side of the opening from which the door was removed. With these screws secure each hinge at the bottom. Tighten the two top screws of each hinge. Reinsert the plastic plugs on the side from which the door was removed. Customer ServiceTroubleshooting TipsOperating InstructionsSafety Instructions 9 Loading and using the dryer. Always follow the fabric manufacturer’s care label when laundering. Safety InstructionsCustomer Service Troubleshooting Tips Operating Instructions Sorting and Loading Hints As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce® Fabric Conditioner Dryer Sheets have been approved for use in all GEDryers when used in accordance with the manufacturer’s instructions. Do not overload. This wastes energy and causes wrinkling. Do not dry the following items: fiberglass items, woolens, rubber-coated items, plastics, items with plastic trim and foam-filled items. Care and Cleaning of the Dryer The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty. The Lint Filter: Clean the lint filter before each use. Moisten your fingers and reach into the filter opening. Run your fingers across the filter. Have a qualified technician vacuum the lint from the dryer once a year. The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged exhaust can lengthen the drying time. Follow these steps: 1 Turn off electrical supply by disconnecting the plug from the wall socket. 2 Disconnect the duct from the dryer. 3 Vacuum the duct with the hose attachment and reconnect the duct. The Exhaust Hood: Check with a mirror that the inside flaps of the hood move freely when operating. Make sure that there is not wildlife (birds, insects, etc.) nesting inside the duct or hood. Fabric Care Labels Below are fabric care label “symbols” that affect the clothing you will be laundering. WASH LABELS DRYLABELS Machine wash cycle cycle Normal Permanent Press/Gentle/ Do not wash Do not wringwrinkle resistant delicate Hand wash Water temperature Hot Warm Cold/cool(50°C/120°F) (40°C/105°F) (30°C/85°F) Tumble dry Dry Normal Permanent Press/ wrinkle resistant Gentle/ delicate Do not tumble dry Do not dry (used with do not wash) Heat setting High Medium Low No heat/air Specialinstructions Line dry/ hang to dry Drip dry Dry flat In the shade BLEACH LABELS Bleach symbols Any bleach Only non-chlorine bleachDo not bleach (when needed) (when needed) 10 Vent...