Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Switch the machine on by pressing the On/Off button. 2. Load your laundry into the machine and shut the door. 3. Add the detergent and any fabric softener. 4. Turn the programme selector dial to the required programme. 5. Select any options you require (see Option Modifiers). 6. Press the Start/Cancel button to start the programme. To stop or change a programme: 1. Press the Start/Cancel button for 3 seconds. 2. Select ‘Pump Out’ on the programme selector dial. 3. When the machine has finished emptying, turn the programme selector dial to the new programme required. You may need to add detergent. 4. Press the Start/Cancel button to start the programme. A typical wash load Two examples of maximum wash loads for different types of fabric: 2 Bath Towels 1 Hand Towel 6 Shirts 6 Blouses 1 Set of Pyjamas 4 Items of Underwear COTTON 6kg 2 Children’s Dresses 4 Shirts 4 Blouses 1 Set of Pyjamas 4 Items of Underwear SYNTHETIC 3kg Did you know that with Hotpoint and Ariel you’ll get the best washing results? Certain laundry products work better in some machines than others. At Hotpoint we know this is true because we’ve done the research to prove it. We used real everyday clothes and ran tests to find out which washing powder works best with Hotpoint. The results proved that Hotpoint and Ariel produces the best washing results on all your clothes. Ariel can meet all your laundry needs. It’s available as a biological powder for everyday wash loads. Colour powder to keep your clothes staying brighter for longer and a Non-Bio powder for when you need brilliant cleaning but are concerned about sensitive skin. 10 Programmes and Option Modifiers Automatic features Unbalanced load detection The machine has an inbuilt feature to prevent it from spinning too fast with an unbalanced load. When an unbalanced load is detected, the machine will attempt to redistribute the load in order to balance it evenly to achieve full spin speed. If this is not possible and an unbalanced load remains the spin speed will be reduced, depending on the amount of unbalance detected. This is to prevent the machine from damaging itself or its surroundings and to prevent excessive noise from the machine. If the spin result is unsatisfactory following a reduced spin speed attempt to rectify the unbalanced load, then on completion of the programme the load can be redistributed evenly in the drum by hand. Select a spin cycle. Note: Do not attempt to spin heavy or absorbent single items as the machine cannot distribute these evenly. If you need to wash a single item you will need to add some other items as ballast to allow the machine to distribute the load evenly throughout the drum. No water detection The machine will automatically detect if it cannot take in water and will notify you by flashing the Prewash light. If this occurs please check the appliance is plumbed in correctly (see Installation Guide) and the water supply is turned on as described in the installation guide that accompanies this booklet. GB Programmes Option Modifiers Safety Technical Wash Labels Contents Description Troubleshooting Advice Details Service Explained 11 Troubleshooting GB If your machine seems not to be working, go through the following troubleshooting suggestions before you call your Service Centre (see Service). Problem: The machine won’t start? The wash cycle won’t start? The machine fails to fill with water? The machine does not drain or spin? The machine makes a noise or vibrates too much during the spin cycle? The machine leaks? Possible causes / Solution: . Check the appliance is fully plugged into the socket and switched on. . Is the socket ok? Try another appliance in the socket to check. . Is the fuse in the plug ok? If not, replace it (see Care and Maintenance). . There has been a power failure. . The appliance door is not shut properly. . The ON/OFF button has not been pressed. . The Start/Cancel button has not been pressed for at least 3 seconds. . The cold water supply tap is not turned on - H20 is displayed (Aquarius+ only). . Aquarius+ only: Have you selected Time Delay (see Programmes and Option Modifiers). . The Start/Cancel button has not been pressed, for at least 3 seconds. . Is the ‘Prewash’ indicator light flashing? This indicates the machine cannot take in water (see Installation), check: -The cold water inlet hose is connected to the tap. -The hose is kinked. -The cold water supply tap is not turned on. -There is a water shortage. -The water pressure is insufficient. . There has been an unbalanced load and the machine could not spin (see ‘Automatic Features’, Programmes and Option Modifiers). . Has the drain hose been installed correctly (see Installation)? . Are the drain hose, standpipe or undersink connections blocked? . Has the ‘Rinse Hold’ option been selected? ‘Rinse Hold’ indicator light will flash. To complete the paused programme press either the Start/Cancel button or the ‘Rinse Hold’ button (see Programmes and Option Modifiers). . Ch...
Otros modelos de este manual:Secadoras - Aquarius+ (310.82 kb)