Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
See “Drying, Cycle, and Temperature Tips.” 3 Select a HEAT setting for appropriate temperature. 4 Press the START button. STOPPING AND RESTARTING Any time during a cycle you can stop your dryer. TO STOP YOUR DRYER Open the dryer door or turn the control dial to OFF. NOTE: When the dryer is not in use the control dial should point to an OFF area. TO RESTART YOUR DRYER 1 Close the door. 2 Select a new cycle and temperature (if desired). 3 Press the START button. LOADING • Place only one wash load in the dryer at a time. • Load clothes loosely into the dryer which allows space for clothes to tumble freely. • Mixed loads of heavy and lightweight clothes will dry differently. Lightweight clothes will dry, while heavy clothes may be damp. • Add one or more similar items to the dryer when only one or two articles need drying. This improves the tumbling action and drying efficiency. • Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some fabrics. • When drying large, bulky items such as a blanket or comforter, it may be necessary to reposition the load during the cycle to ensure even drying. • Do not pack the dryer. PLEASE REFER TO PAGE 7 OF THE WHIRLPOOL USE & CARE GUIDE FOR ADDITIONAL INFORMATION ON LOADING. DRYING, CYCLE AND TEMPERATURE TIPS PLEASE REFER TO PAGE 8 OF THE WHIRLPOOL USE & CARE GUIDE. CYCLES PLEASE REFER TO PAGE 8 OF THE WHIRLPOOL USE & CARE GUIDE. CARE & CLEANING CLEANING THE LINT FILTER Clean the Lint Filter: • After each load. • To shorten drying time. • To operate more energy efficiently. The lint filter can be found on the top of the dryer. Drying time can be increased if your filter is clogged by lint. To clean 1 Pull the lint filter towards you. Roll lint off the filter with your fingers. Do not rinse or wash filter to remove lint. Wet lint is hard to remove. 2 Push the lint screen firmly back into place. IMPORTANT: • Do not run the dryer with the lint filter loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics. • Some towels made of synthetic fibers and natural fibers (polyester and cotton blends) may shed more lint than other towels, causing your dryer’s lint filter to fill up faster. Before and after drying new towels be sure to remove lint from the lint filter. • Check the exhaust hood and remove the lint if lint falls off the filter into the dryer during removal. See “Checking Your Vent.” As needed cleaning: Laundry detergent and fabric softener residue can build up on the lint filter. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. If lint falls off the filter it is probably clogged. Clean the lint filter with a nylon brush about every six months, or more frequently if it becomes clogged due to a residue buildup. To wash 1 Use your fingers to roll lint off filter. 2 Use hot water and wet both sides of lint filter. 3 Use hot water and liquid detergent to wet a nylon brush. To remove residue buildup scrub lint filter with the brush. 4 Use hot water to rinse filter. 5 Use a clean towel to thoroughly dry lint filter. Insert lint filter back into dryer. CLEANING THE DRYER INTERIOR PLEASE REFER TO PAGE 9 OF THE WHIRLPOOL USE & CARE GUIDE. REMOVING ACCUMULATED LINT PLEASE REFER TO PAGE 9 OF THE WHIRLPOOL USE & CARE GUIDE. TROUBLESHOOTING GUIDE PLEASE REFER TO PAGE 10 OF THE WHIRLPOOL USE & CARE GUIDE SERVICE, PARTS OR ASSISTANCE Please refer to ‘Troubleshooting’ on page 10 of the Whirlpool Use & Care Guide before calling for service or assistance. It may save you the cost of a service call. Please follow the instructions below if you still need help. Please know the purchase date, model number, and serial number of your dryer when calling. This information will be helpful for us to better respond to your request. If you need replacement parts, assistance, or service Please call Staber Industries at 614-548-0098. STABER DRYER WARRANTY WARRANTY COVERAGE ONE YEAR FULL WARRANTY FROM DATE OF PURCHASE When this dryer is operated and maintained according to instructions attached to or furnished with the product, Staber Industries will be responsible for: Replacement parts and/or repair labor with prior written authorization to correct defects in materials or workmanship. SECOND THROUGH THIRD YEAR LIMITED WARRANTY FROM DATE OF PURCHASE When this dryer is operated and maintained according to instructions attached to or furnished with the product, Staber Industries will be responsible for: Replacement parts to correct defects in materials or workmanship, with the owner paying all other costs, including labor, mileage and transportation. Staber Industries will not be responsible for: a. Service calls to: a. Correct the installation of the dryer, including venting. Heavy 4 inch (10.2 cm) metal exhaust vent must be used. Refer to the venting section of this manual and your Installation Instructions. b. Instruct you how to use...
Otros modelos de este manual:Secadoras - HXD2304E (39.16 kb)