Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
A Condensed water is not drinkable! C You can use the water in the water tank in your steam irons or air humidifiers. A Never take out the water tank when the programme is running! Water tank may be located in two different places as indicated below, depending on the model of your machine. Inside the drawer on the panel- Inside the kick plate cover- If you forget to drain the water tank, your machine will stop during the following drying cycles when the water tank is full and the “Water tank” warning LED will light on. If this is the case, press the “Start/Pause/Cancel” button to resume the drying cycle after draining the water tank. In order to drain the water tank; 1 Carefully remove the water tank by opening the kick plate cover/pulling the drawer. 2 Drain the water by opening the water tank cover. 3 If there is lint accumulation in the water tank cover, clean it and press to close. 4 Place the water tank into its seat. For the condenser (products equipped with a condenser); Hot and humid air in the condenser is cooled with the cold air from the room. Thus, the humid air circulating in your machine is condensed and then pumped into the tank. C Clean the condenser after every 20 drying cycles or once a month. To clean the condenser; 1 If a drying process has been carried out, open the door of the machine and wait until it cools down. 2 Unlock the 4 condenser locks after opening the kick plate. 3 Pull out the condenser. 4 Clean the condenser with pressurized water and wait until the water drains. 5 Replace the condenser with the side labeled “Top” facing upwards. Lock the 4 condenser locks. Make sure that the red lock on the upper right corner is engaged securely. 6 Close the kick plate cover. Close properly and check the locking latchs? 9 Solution suggestions for problems Problem Cause Explanation / Suggestion Drying process takes too much time. Cover filter and filter drawer might have not been cleaned. * Clean the cover filter and Filter drawer. Laundry come out wet at the end of drying. * Cover filter and filter drawer might have not been cleaned. * Excessive laundry might have been loaded in. * Clean the cover filter and Filter drawer. * Do not overload the machine. Machine does not switch on or the programme does not start. Machine is not activated when set. * It might have not been plugged in. * The loading door may be ajar. * Programme might have not been set or the “Start/Pause/Cancel” button might have not been pressed. * “Childproof lock” might have been activated. * The condenser cover on the models with a condenser might not be closed securely. * Make sure that the machine is plugged in. * Make sure that the loading door is properly closed. * Make sure that the programme has been set and it is not in “Pause” mode. * Deactivate the childproof lock. * Make sure that the condenser cover and the red lock is closed securely. Programme has been interrupted without any cause. * The loading door may be ajar. * Electricity may be cut off. * Make sure that the loading door is properly closed. * Press “Start/Pause/Cancel” button to start the programme. Laundry has shrunk, become felted or deteriorated. * A programme suitable for the laundry type might have not been used. * Dry only the laundry which is suitable for drying in your machine after checking the labels on your clothes. * Select a programme with suitable low temperature for the laundry type to dry your clothes. Drum lightning does not come on. (for models equipped with a lamp) * The machine might have not been started by using the On/Off button. * Bulb may have blown. * Make sure that the machine is On. * Call the authorized service to replace the bulb. “Final / Anti- creasing” LED flashes. * The 2-hour anti creasing programme to prevent laundry from creasing might have been activated. * Turn off the machine and take out the laundry. “Final / Anti- creasing” LED is on. * Program has come to an end. * Turn off the machine and take out the laundry. The “Drying” LED flashes. * A heat sensor failure has occurred. Machine ends the programme without heating. * Turn off the machine and take out the laundry. Call your authorized service. “Filter cleaning” LED flashes. * Filter might have not been cleaned. * Clean the cover filter. Also for products equipped with a condenser “Water tank” warning LED is on. * Water may be full. * Anti-creasing programme might be running. * Drain the water in the water tank. “Condenser cleaning” LED is on. * Filter drawer/Condenser might have not been cleaned. * Clean the filters in the condenser/filter drawer under the kick plate. A Call an authorized service agent if the problem persists. 10 Door Reversal 1. Unplug the dryer. 2. Open the door. 3. Turn the contact pin in the upper part of door by 90° in the anti-clockwise direction and remove it. 4. Unscrew the 2 screws of each door hinge and remove the door. 5. Removing the door lock: Using a flat screwdriver release the snap-fitted door lock. 6. Remove 2 plugs for the ...
Otros modelos de este manual:Secadoras - DRVS 62 S (718.16 kb)