Votos - , Puntuación media: ( )

Manual de usuario Miele, modelo T8002

Fabricar: Miele
Tamaño del archivo: 727.16 kb
Nombre del archivo: 213ffa33-7563-4315-a011-096d90a13106.pdf

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

A 3 pole-4 wire grounding power outlet (NEMA type 14-30 R) is necessary. Installation a Exhaust connection: The exhaust hose can be installed either at the rear, left or right of the dryer. b Power cord with plug c Control panel d Door e Four height adjustable feet Installation Rear view Installation site a Handle for easy transport (arrows) b Power cord with plug c Vent connection rear ,Do not install the dryer in a location where its door could conflict with room doors. ,This appliance is not intended to be mounted in a wall or other vertical surface of a building or cabinet. The unit is allowed for built-in application. Transporting the dryer to the installation site The rear excess end of the lid has a handle for transport. ^ Use the front dryer feet and the rear excess end to transport the dryer from the packaging base to the installation site. Installation Installation beneath a counter ,When removing the machine lid to reduce the height of the machine, a built under spacer kit* is necessary. It must be installed by a Miele Service Technician. The cover plate of the built under kit replaces the appliance lid and ensures electrical safety. An installation manual is supplied with the built-under spacer kit. The electrical connection should be near the dryer and accessible at all times. Provide necessary space for the ducting when planning the undercounter installation. Extended machine feet* are recommended at a built-in height of more than 33 1/16" (840 mm). ^ Set the extended machine feet at a height of 1 9/16" (40 mm). Remove the original machine feet and replace them with the extended ones. One or two filler frames* are recommended at a niche height of 34 1/4" to 34 13/16" or 36" to 36 5/8" (870-885 / 915-930 mm). * (optional accessory) Reinstallation of the machine lid ^ When reinstalling the appliance lid, check the firm fit of the cover at the rear bracket for safe transport of the dryer. An existing continuous toe kick must be interrupted at the dryer location! Installation Leveling the dryer The dryer must be level to ensure safe and proper operation. Minor discrepancies do not however, have an adverse effect on operation. Determining the position of the exhaust connection The exhaust connection can be left at the rear of the dryer (factory standard) or moved to the left or right side of the dryer. Changing the position of the exhaust connection ^To remove the exhaust connection cover on the left or right side of the dryer turn it counterclockwise and take it out. ^Firmly press the cover into the rear opening. The machine can be leveled by turning the legs clockwise or counterclockwise as necessary. Installation Installation tips An airflow gap of 3/8" (10 mm) must be provided between the machine and the floor. This airflow gap must not be blocked by a toekick or thick piled carpets. Do not install the dryer next to a refrigerator. The warm air exhausting from the dryer can affect the thermostat of the refrigerator, causing it to run continuously. Installation Exhaust connection with a Window connection flexible exhaust hose or rigid pipe Using the connector supplied, an exhaust hose (4" [100 mm] diameter) can be installed. Necessary materials: – a wall or window duct (available from Miele) – an exhaust hose made of approved non-flammable material ^ Install the exhaust hose or pipe, 2, with the connector, 1, to the dryer. 1 Window duct ( (installed in a plexiglass pane) 2 Connector for the flexible exhaust hose Wall connection with rigid pipe 1 Wall pipe (Installation sheet supplied with the Miele wall pipe) 2 Connector 3 Rigid pipe Direct wall connection Necessary materials: – a wall pipe – flexible foam gasket Dryer top view 1 Wall pipe 2 Flexible foam gasket Dryer side view 1 Wall pipe 2 Flexible foam gasket ^ Connect the flexible foam gasket, 2, to the wall pipe connector, 1. ^ Push the dryer to the wall. Installation 31 Installation How to calculate the effective duct length The overall duct length will determine the duct diameter. ^ Measure the actual duct length needed to go from the dryer’s exhaust connection to the vent outlet: 1. Establish the number of elbows or bends necessary, noting the type of bend, angle and radius involved (see Table). 2. Add the additional duct length (as derived by using the values specified in the table) and the actual duct length to get the effective length. Note: Maximum effective duct lengths: 4" (100 mm) diameter 66 ft (20 m) 5" (125 mm) diameter 132 ft (40 m) 6" (150 mm) diameter 328 ft (100 m) Using the ring adapter up to an effective duct length of 33 ft (10 m) and a standard duct diameter of 4" (100 mm) will provide optimal drying times and energy consumption. Do not use the ring adapter if the effective duct length is more than 33 ft (10 m). Effective duct lengths over 66 ft (20 m) require a larger duct diameter. Longer ducts may lead to slight decreases in dryer efficiency if the necessary duct diameter is not employed. Tips about the ductwork – Ch...