Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
^ Empty the condensed water container weekly (if not connected to a drain). Using the dryer Canceling or changing a program ^ Press and release the "Start/Stop" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or -button. ^ Select any desired options. ^ Select a dryness level (available in the "Normal" and "Wrinkle-free" programs). ^ Press and release the "Start/Stop" button to start the new program. Adding or removing laundry during a program ^ Turn off the dryer using the "On/Off" button. ^ Press the "Door" button. ^ Open the door. ,CAUTION -Do not touch the rear of the drum while adding or removing items! There is a danger of burns due to high temperatures in the drum. ^ Add or remove items. ^ Close the door. ^ Turn the dryer back on with the "On/Off" button. Child lock Child lock When activated, the child lock prevents the dryer from being operated by locking the control panel functions. The dryer can be turned on but not started. The "Child lock" indicator will flash. The door can be opened. To activate the child lock 1. Make sure the dryer is turned off and the door is closed. 2. Press and hold the "Anti-crease" and "DRYNESS" buttons at the same time, hold until step 5. 3. Turn on the dryer with the "On/Off" button. 4. Press the "OPTIONS" button 3 times. 5. Release the "Anti-crease" and "DRYNESS" buttons. The "Child lock" indicator will flash and the dryer is now locked. 6. Turn off the dryer using the "On/Off" button. To deactivate the child lock Repeat steps 1. to 5. The "Child lock" indicator will go out. The control panel is now unlocked. 6. Turn off the dryer using the "On/Off" button. Dryer care Cleaning the lint filter The lint filter must be cleaned after every program. ^ Remove the lint from the door frame lint filter with your fingers. ^ Any lint remaining in the hollow casing of the door can be removed through the gap at the bottom with a dust brush or vacuum. ^ Clean the gasket 2 with a damp cloth. ^ Return the lint filter and close the door. ^ Open the door and remove the lint filter 1 by gently lifting it upwards. The lint filters (once removed from the dryer) can be rinsed with hot water if necessary. The filters must be dried thoroughly before being returned to the dryer. ^ Take the door lint filters out by turning the knob at the filter top. ^ Wipe the lint off the filter with your hand (do not use any sharp objects!) Dryer care Cleaning the exterior and the control panel ,To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the dryer. They will damage the surface. ^ The exterior and the control panel can be cleaned with warm water and liquid dish soap applied with a soft sponge. ^ Wipe dry. Cleaning the drum ^ The stainless steel surfaces of the drum can be cleaned using a non-abrasive stainless steel cleaner. ^ Wipe clean with a soft cloth. Dryer care Emptying the condensed water container Depending on the installation, the condensed water will either be pumped to a drain or collected in the condensed water container, located in the upper left corner of the machine. The container holds approximately 1 gallon of water. The container should be emptied weekly. Should the container be full when the ^ Pull out the container slightly to the tumble dryer is started, or if it becomes right with both hands. full during normal operation: – The "Container" indicator will light. – The buzzer will sound. ^ Hold the cap open while emptying the container. ^ When the container is empty, push it back into its opening until it clicks into place. ^ Restart the drying program if needed. Do not drink the condensed water! Dryer care Cleaning the condenser Removing the condenser ^ Open the door. ,To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Detergent residues, hair and lint in the drying air can penetrate filters and clog the condenser. Particles from the cool air sucked in from the install location can cause blockages. ^ Check the condenser at least twice a year. If used often, check every 100 loads. ^ Clean if necessary. ^Open the access panel, located on the lower left corner of the machine, using the yellow tool supplied with the machine. Hold the panel when opening it. ^ Remove the panel up and out of the condenser access area. ^ Turn the condenser door lock down and remove the door. Dryer care ^ Turn the condenser lock up. ^ Pull out the condenser. Checking the condenser ^ Hold the condenser against the light. ^ Look through the front and left side (as illustrated above) of the condenser to check for lint. If no lint is visible: ^ Return the condenser. If lint is visi...