Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Remove thermostat. 5. Reestablish power to dryer. I 25 To Replace Lint Compartment Hi-Heat Protector (225 Degree) Thermostat This thermostat is part of the "sensor bracket assembly" and is secured to the underside of the basket wrapper in the lint compartment. As a safety device, this thermostat will open (shut off) the heating unit circuit if an excessive temperature occurs. The dryer motors will remain on, even if the thermostat is open. IMPORTANT: Under no circumstances should heat safety devices be disabled. 1. Discontinue power to dryer. 2. Remove lint drawer. Remove two (2) screws securing lint door and remove lint door. 3. Locate sensor bracket assembly and loosen the two (2) Phillips head screws securing bracket assembly to the tumbler wrapper. NOTE: Do not remove the screws. 4. Remove bracket assembly by slightly sliding bracket towards the rear of the dryer and to the left. 5. Disconnect sensor bracket harness connector and remove bracket assembly from dryer. 6. Disconnect the two (2) orange wires from the thermostat. 7. Disassemble thermostat from bracket assembly by removing the two (2) mounting screws, washers, and nuts. 8. Reverse this procedure for installing a hi-heat protector thermostat. 9. Reestablish power to the dryer. D. Sail Switch Assembly (Gas Models Only) The sail switch is a heat circuit safety device which controls the burner circuit only. When the dryer is operating and there is proper airflow, the sail switch damper pulls in and closes the sail switch. Providing all the other heat-related circuits are functioning properly, ignition should now be established. If an improper airflow occurs, the sail switch damper will release, and the circuit will open. THERMOSTAT 26 To Replace Sail Switch 1. Disconnect power to dryer. 2. Remove the two (2) screws which hold sail switch box cover to sail switch box. 3. Disconnect the two (2) wires from the switch. 4. Disassemble sail switch from mounting bracket by removing the two (2) screws securing switch in place. 5. Reverse this procedure for installing new sail switch. Adjust sail switch as described in the next section. To Adjust Sail Switch With the dryer operating at a high temperature setting, pull the sail switch away from the burner. The sail switch should open and extinguish the burner. Let the sail switch damper return to the burner wall. The sail switch should close to restart the burner ignition cycle. If the sail switch circuit does not operate as described, bend the actuator arm of the sail switch accordingly until proper operation is achieved. To check proper "open" position of sail switch, open main door, manually depress main door switch, and start dryer. With the main door open and the dryer operating, the sail switch should be open, and the burner should not come on. CAUTION: Do not abort this switch by taping or screwing sail switch damper to burner. PERSONAL INJURY OR FIRE COULD RESULT. E. Front Panel and Main Door Assemblies To Replace Main Door Switch 1. Discontinue power to dryer. 2. Open main door. 3. Remove the two (2) Phillips head screws holding the main door switch bracket assembly in place. 4. Remove door switch bracket from hinge block and disconnect wiring from switch. 5. Disassemble door switch bracket by removing locking adjustment nut. Remove second locking nut and assemble onto new door switch. 27 6. Reverse this procedure for installing new door switch. 7. Reestablish power to dryer. IMPORTANT: Under no circumstances should the door switch be disabled. To Replace Main Door Assembly 1. Remove screws holding main door to main door hinge pad. 2. Reverse this procedure for reinstalling new main door assembly. To Install New Main Door Glass 1. Remove main door assembly from dryer (follow main door removal procedure). 2. Lay main door on flat surface with front of door face down. 3. Remove glass and clean all old sealant off main door. This area must be completely cleaned for correct bonding. MAN05ifl 4. Apply a narrow bead of silicone (ADC P/N 170730) all around main door area where glass will rest. 5. Install glass onto door/adhesive and slightly press glass in place. IMPORTANT: Do not press hard or silicone thickness between the glass and door will be reduced, resulting in poor bonding. 6. The door assembly should now be put in an area where it will not be disturbed for at least 24 hours. Depending on the conditions, the curing time of this adhesive is 24 to 36 hours. 7. After 24-hour curing period, install main door on dryer by reversing step 1. 28 To Replace Front Panel 1. Discontinue power to dryer. 2. Remove main door switch and bracket assembly. 3. Follow procedure for removal of main door assembly. 4. Open control (service) door. 5. Remove lint drawer and open lint door by removing two (2) screws. 6. Remove the twelve (12) Phillips head screws securing front panel to dryer. 7. Pull wires up through front panel door switch wire channel and ge...