Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Excessive steam pressure can damage steam coil and/or harm personnel. 13. Replace leaking flexible hoses or other steam fixtures immediately. DO NOT operate the dryer with leaking flexible hoses. PERSONAL INJURY MAY RESULT. 14. READ AND FOLLOW ALL CAUTION AND DIRECTION LABELS ATTACHED TO THE DRYER. 15. For safety, proper operation, and optimum performance, the dryer must not be operated with a load less than sixty-six percent (66%), 204 lbs. (92.53 kg.) of its rated capacity. WARNING: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND THE GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, OR TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health Administration) STANDARDS. 5 SECTION II SPECIFICATIONS/DIMENSIONS AND COMPONENT IDENTIFICATION A. SPECIFICATIONS (GAS AND STEAM) MAXIMUM CAPACITY (DRY WEIGHT) 310 lbs 141 kg BASKET (TUMBLER) DIAMETER 62-1/2” 158.75 cm BASKET (TUMBLER) DEPTH 60” 152.4 cm BASKET (TUMBLER) VOLUME 106.5 cu. ft. 3.02 cu. m. DRIVE MOTOR 5 HP 3.73 kw DOOR OPENING (DIAMETER) 36-3/4” w x 43” h 93.3 cm x 109.2 cm DOOR STILL HEIGHT - LEVEL 36-1/2” 92.71 cm COMPRESSED AIR 80 PSI 5.51 bars COMPRESSED AIR CONNECTION 3/8” F.P.T. Gas* VOLTAGE AVAILABLE 208-600v 30 3 , 4w 50/60 Hz BLOWER MOTOR 15 HP 11.25 kw HEAT INPUT 1,125,000 btu/hr 283,500 kcal/hr APPROX. WEIGHT (UNCRATED) 5,100 lbs 2,314 kg AIRFLOW 6,500 cfm 184.1 cmm INLET PIPE SIZE 1-1/2” Steam* VOLTAGE AVAILABLE 208-600v 30 3, 4w 50/60 Hz BLOWER MOTOR 25 HP 18.64 kw APPROX. WEIGHT (UNCRATED) 5,600 lbs 2,540 kg AIRFLOW 8,500 cfm 240.7 cmm STEAM CONSUMPTION BOILER HP NORMAL LOAD 1,153 lbs/hr 524 kg/hr 55 OPERATING STEAM PRESSURE STEAM SUPPLY STEAM RETURN 125 PSI max 8.62 bars 2” 2” Shaded areas are stated in metric equivalents * Dryers must be provided with a clean, dry, and regulated 80 PSI +/- 10 PSI (5.51 bars +/- 0.68 bars) air supply (equivalent volume = 9 cfh [0.25 cmh]). NOTE: ADC reserves the right to make changes in specifications at any time without notice or I obligation. 6 B. DIMENSIONS AND COMPONENT LOCATION 310 NON-TILT GAS MODEL ST ShWvKLfft WA TER / \£9№5TT5fv * №i / \ / _ Z4" <6Q ^ ml VIA / EXHAUST DIJCT * *** 2'£9 TWO * V4m /rf*T DAS COfoNfCnOlfoS 7 EXHAUST DUCT 310 NON-TILT STEAM MODEL 21In 2 V4 in 53 in 9 V4 in 172 an EXHAUST DUtT 24" (60,96 avl 01A METER 1473 ao 23.49 cm r &A - STEAM SUPFLY CONNECWN 2‘ D/A CQN0ENSA7E RETURN ZVt^CTON } \_LW DPAWEP $P£:T50? 5535 cJii LEFT SIDE VEW i STEAM UNITS MUST BE SUPPLED WUfi 'CLEAN, DRY. RE&JLATED AIR AT 39 P5I */-10 PS iSS' tors */- DfiS isarel FRONT WEW 8 SECTION III INSTALLATION PROCEDURES Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, the installation must conform to applicable American National Standards: ANSI Z223. 1-LATEST EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST EDITION (National Electrical Code) or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST EDITION (for General Installation and Gas Plumbing) or Canadian Electrical Codes Parts 1 and 2 CSA C22.1-1990 or LATEST EDITION (for Electrical Connections). A. REASSEMBLY OF DRYER IMPORTANT: Always keep the basket (tumbler) section of the dryer in an upright position when moving it. The dryer may be shipped one (1) of two (2) ways; as a complete unit fully assembled and ready for hookup or with the basket (tumbler)section separated from the base. If the dryer is shipped in two (2) pieces, the basket (tumbler) section will have to be lifted onto the base. Use cables through the eyebolts on top of the basket (tumbler) section, or use a forklift for the lifting process. 9 1. Reassembly Instructions For Gas Dryer Shipped In Two (2) Pieces END OF CYCLE LIGHT VEW 1 A PLACES MA N5601 DM G 01/24/01 HARDWARE 10 HI a. Reassembly Instructions For Non-Tilt Gas Dryers: Lift the basket (tumbler) section onto the base. 1) The dryer has four (4) support posts assemblies which are located in each corner of the base. On top of each post assembly is a clevis block which must be bolted to the basket (tumbler) section. Use the 4-1/2” diameter x 1-1/8” long bolts and lock washers to bolt each clevis block to the basket (tumbler) section. (Refer to View 1 on the previous page.) 2) Basket (tumbler) power cable reconnection: a) A plug and cable is located in the right of the base. This must be lifted up and reconnected into the mating socket located at the bottom of the right basket (tumbler) section. b) Pull the basket (tumbler) section power cable up from the left side of the base through the hole in the bottom of the basket (tumbler) section. Reconnect the wires of this cable into the 2-inch x 4-inc...