Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Check for voltage across pin #2 of the 6 pin connector (J10) and ground. If no voltage is evident, problem could be faulty transformer (P/N: 141403). If voltage is evident then continue with step #3. 3. Check for voltage on pin # 2 of the 6 pin connector (J3) located near the temperature sensor bracket assembly and the ground. If no voltage problem is a bad wire or termination between the (J10 & J3) connectors (pin # 2). 4. Check for voltage on the two (2) four pin connectors (J8, J9) of the lint switch assembly & ground.. 6 PIN CONNECTOR BDl mm mm MAN2509 46 NOTE: Each connector has 2 connections on them (pin #'s 2 & 4) A) If voltage is not present on all 4 pins of those two connectors (J8,J9) the problem is a bad wire or termination on the main door switch or the lint drawer switch or any wires associated with these devices. 5. Check for voltage on pin # 1 of the 6 pin connector (J3) and ground, also check for voltage across pin # 1 of the 6 pin connector (J10) with respect to ground. If no voltage, problem is bad wire or termination between the (J10) and the (J3) connectors pin # 1. 6. Check for voltage on pin # 9 of the 9 pin connector (J2) and ground.. If no voltage, problem is bad wire or termination between the (J2) pin # 9 and the (J10) pin # 1. 7. Check for voltage on the computers 9 pin connector, pin # 9 and ground. If no voltage, problem is bad wire or termination between the computers 9 pin connector, pin # 9 and the (J2) connector, pin #9. If voltage replace computer. 47 SECTION VII TECHNICAL INFORMATION A. DATA LABEL Contact American Dryer Corporation UOOEL SERIAL NO. ADG-530 345947 KD UANUFACTUFUNQ CODE NUMBER 6305147130317010840X00000000000000 204,000 BTU MAX TYPE OF HEAT HEAT NPUT GAS/NATURAL . “ 102.000 BTUH PER POCKET ELEOTRK3 SERVICE (2) 115W60HZ/1PH 6 AMPS PER POCKET GAS MANFOLD PRESSURE 3.5 IN WC FOR USE WITH NATURAL AND LP. OASES ^RTr ANS 221.52 b.1992 CLOTHES DRYER VOL II 24 VOLT CONTROL VOLTAGE When contacting American Dryer Corporation certain information is required to insure proper service/parts information from American Dryer. This information is on the data label located on the control door. When contacting American Dryer please have the model number and serial number handy. DATA LABEL 1. MODEL NUMBER—The model number is an ADC number which describes the size of the dryer and the type of heat (gas or steam). 2. SERIAL NUMBER— The serial number allows ADC to gather information on your particular dryer. 3. MANUFACTURING CODE NUMBER— The manufacturing code number is a number issued by ADC which describes all possible options on your particular model. 4. TYPE OF HEAT— Describes the type of heat; gas (natural or L.P.) or steam or electric. 5. HEAT INPUT— (For gas dryers) describes the heat input in British thermal units. 48 6. ELECTRIC SERVICE— Describes the electric service for your particular models. 7. GAS MANIFOLD PRESSURE— Describe the manifold pressure as taken at the gas valve pressure tap. (see HOW TO USE A MANOMETER) B. USING A MANOMETER HOW TO USE A MANOMETER (ADC P/N: 122804) 1. With dryer in non-operating mode remove plug on the gas valve pressure tap. 2. Attach plastic tubing to pressure tap. (Fitting is supplied with manometer see illustration.) 3. Attach manometer to dryer using magnet. NOTE: Place manometer in a position so that readings can be taken at eye level. 4. Fill manometer as shown in illustration to the ^ zero level. 5. Start dryer. With burner on take a reading. PHtSSUKfc 1 AH GAS VALVE- A. Read water level at the inner tube. Readings should be taken at eye level. B. Correct readings should be: NATURAL GAS: 3.5 - 4.0 inches w.c. L.P. GAS: 11 -10.5 inches w.c. 6. If water column pressure is incorrect refer to "TO ADJUST GAS PRESSURE" 7. Reverse procedure for removing manometer. OUTER TUBE PLASTIC TUBNG PU. WITH WATER TO ZERO LEVEL 49 C. L.E.D. DISPLAY CODES A Automatic Cycle (Slope Program Factor) ACOn Accumulative Coin Adrt Maximum Auto Dryness Time AFAt Amount for Additional Time AGt Active Anti-Wrinkle Guard Time Atln Accumulative Time AtSt Amount Start AUtO Automatic Mode (Patent No. 4,827,627) b Automatic Cycle (Heat loss [offset] Factor) bCLO Bad Coin Lockout bCrS Bad Coin Reset bUZ Buzzer (Tone) CEL Degree in Celsius CLCC Clear Left Coin Count COIn Coin Mode CrCC Clear Right Coin Count donE Drying and Cooling Cycles Complete or Dryer is in Anti-Wrinkle Cycle door Door Circuit is Open dSFL Dryer Sensor Circuit Failure FAr Degree in Fahrenheit FELL No Cycle in Progress FLS Flash Display Active FrEE Dry Mode GdLY Anti-Wrinkle Delay Time Gont Anti-Wrinkle On Time Grd Anti-Wrinkle Program Active HICd High Cool Down Temp Hot Overheating Condition LCC Left Coin Count LCde Left Coin Denomination LOCd Low Cool Down Temp nbUZ No Buzzer (Tone) in FLS No Rash Display Ngrd No Anti-Wrinkle nSEn Rotational Sensor Not Selected PdrY Percent Dry PL Program Locat...