Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The corresponding light comes on. Time Use the TIME button to select the programme duration after setting the TIME programme. You can select a programme duration from 20 min. to 3 hours in 10-minute steps. 1. Turn the programme selector to the programme. 2. Press the button repeatedly until the desired programme duration is shown in the display, e.g. for a pro gramme of 20 minutes. If the programme duration is not selected, the duration is automatically set to 10 mins. Delay start With the DELAY button, you can delay the start of a programme by between 30 minutes (30') and a maximum of 20 hours (20h). 1. Select the programme and additional functions. 2. Press the Delay button as many times as necessary until the required time of the delay appears on the display, e.g. H if the programme is to be started in 12 hours. If the display is showing H and you press the button again, the time delay will be cancelled. The display will show 0 and then the duration of the selected programme. 3. To activate the delay timer, press the Start/Pause button. The amount of time remaining until the programme is set to start is continuously displayed (e.g. 15h, 14h, 13h, … 30' etc). Setting child lock The child lock can be set to prevent a programme being accidentally started or a programme in operation being accidentally changed. The child lock function locks all buttons and the programme knob. The child lock can be activated or deactivated by holding down the BUZZER and TIME buttons simultaneously for 5 seconds. – Before programme is started: Appliance cannot be used – After programme is started: Programme in operation cannot be changed The icon appears in the display to indicate that the child safety device is activated. The child safety device is not deactivated once the programme comes to an end. If you want to set a new programme, you must first deactivate the child safety device. Starting the programme Press the START / PAUSE button. The programme is started. The programme phase is shown in display by appropriate icons. From left to the right, from drying ,anticrease , to cooling . Changing programme To change a programme which has been selected by mistake once the programme has started, first turn the programme selector to " O" (OFF) position. The programme is cancelled. The programme can no longer be changed directly once the programme has started. If nevertheless there is an attempt to change the programme on the programme knob or if an function button (excluding the button) is pressed, led above START/PAUSE button starts flashing temporarily in yellow. The drying programme is not however affected by this (laundry protection). Drying cycle complete / removing laundry Once the drying cycle is complete, display shows a blinking " 0 ", under anti-crease and filter icon appear dash. If the (Buzzer) 10 electrolux button has been pressed, an acoustic signal sounds intermittently for about one minute. The drying cycles are automatically followed by an anti-crease phase which lasts around 30 minutes. The drum rotates at intervals during this phase. This keeps the laundry loose and free of creases. The laundry can be removed at any time during the anti-crease phase. (The laundry should be taken out towards the end of the anti-crease phase at the latest to prevent creases from forming.) If (Long anticrease) function has been selected, the anti-crease phase is lengthened by 60 minutes. Cleaning and maintenance 1. Open door. 2. Remove laundry. 3. Remove filter after clothes has been removed. Clean the filter. Warning! Before You place the filter, please check it there is nothing inside the filter seat. 4. Turn the programme selector to "O" (OFF) . Important! Clean the filter after each drying cycle. 5. Close the door. Warning! The tumble dryer is not to be used if industrial chemicals have been used for cleaning! Cleaning fluff filter The filter collect all the fluff which accumulates during drying. To ensure that the dryer works perfectly, the fluff filter must be cleaned after every drying cycle. The warning light FILTER , is on to remind you this operation. Caution! Never operate the dryer without fluff filter or with damaged or blocked fluff filter. 1. Open loading door and remove laundry. 2.Remove the filter which is built into the lower part of the loading aperture. 3. Open the filter pressing the button, among two slots on fingers. Clean the filter using dump hand or cloth. After a period of time, a patina due to detergent residue on laundry forms on the filters. When this occurs, clean the filter with warm water using a brush. Close the filter and do not forget to put it back. Warning! Before You place the filter, please check it there is nothing inside the filter seat. 4. The filter can be positioned only to one side. If position is wrong, the filter overhangs. If the filter will not snap into place, the loading door cannot be closed. electrolux 11 Cleaning the door Clean periodically the interior part of the door to remo...