Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
• WARNING: Water in excess of 100 degrees Fahrenheit may be hazardous to your health. • WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. • A green colored terminal marked “Grounding” is located inside the wiring compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment. • One bonding lug for US models (two for Canadian models) is provided on the external surface. To reduce the risk of electric shock, connect the local common bonding grid in the area of the swimming pool, spa, or hot tub to these terminals with an insulated or bare copper conductor not smaller than 8 AWG US / 6 AWG Canada. • All field installed metal components such as rails, ladders, drains, or other similar hardware within 3 meters of the pool, spa or hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than 8 AWG US / 6 AWG Canada. • SAVE THESE INSTRUCTIONS Table of Contents Introduction 1. Preparing Pool/Spa Water 2. Mounting Equipment 3. Plumbing 4. Electrical Wiring 5. Configuration 6. System Startup and Checkout 7. Warranty Before You Begin................................................................... 1 Installation Steps.................................................................... 2 General Water Chemistry..................................................... 2 Salt.......................................................................................... 3 Pro Logic Control Center....................................................... 5 Temperature Sensors............................................................. 5 Optional Chlorination .............................................................. 5 Optional AQL-CHEM Sensing Kit......................................... 5 Optional AQL-CHEM2 CO2 Dispense Kit............................ 6 Optional Remote Controls..................................................... 6 Optional Base Station............................................................ 7 Optional Valve Actuators........................................................ 7 Pool/Spa Configuration.......................................................... 8 Turbo Cell.................................................................................... 9 Flow Switch............................................................................. 9 Main Service........................................................................... 10 Grounding and Bonding......................................................... 10 Circuit Breaker Installation and Wiring.................................. 10 General Purpose Outlet........................................................... 11 Pro Logic Control Power....................................................... 11 High Voltage Pool Equipment............................................... 11 Low Voltage Wiring................................................................ 13 Configuration Menu................................................................ 20 Before Startup........................................................................ 30 Heater Checkout.................................................................... 30 Service Mode......................................................................... 31 Pro Logic Limited Warranty...................................................32 Introduction Before You Begin What’s Included Before attempting to install the Pro Logic system, check that the following components have been included in thepackage: Pro Logic Electronics Unit (3) Temperature sensors with 15 ft. (5m) cable, hose clamp What’s NOT Included Some of the additional items that you may need to complete an installation include: Circuit breakers None are included with control—see page 10 and inside of door for suitable breakers Wire 4-conductor cable (electronics unit to remote display/keypad) Wire/conduit for 100A service from main panel to Pro Logic Wire/conduit for filter pump and other high voltage loads Wire for bonding Miscellaneous Utility electrical outlet and weatherproof cover (for mounting on side of Pro Logic) Mounting hardware (screws, etc.) for mounting Pro Logic and remote display/keypad Valves (use standard Hayward, Pentair/Compool, or Jandy valves) Additional valve actuators Accessory Products - Order Separately T-CELL-3 Chlorinator Cell (for pools up to 15k gallons) T-CELL-9 Chlorinator Cell (for pools up to 25k gallons) T-CELL-15 Chlorinator Cell (for pools up to 40k gallons) P-KIT Chlorination plumbing kit containing flow switch and cell unions AQL-CHEM ORP & pH sense kit AQL-CHEM2(-240) pH dispense kit AQL-WW-P-4 Wired Wall Mount Remote Display AQL-SS-6B-x (x=W/B) Wired Spa Side 6 Function Remote Control, 150ft cable, specify color (w...