Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Selecting a Location loc_2 3/96 - Ref. 151 556 / 802 183 1 Lifting Handles Use handles to lift unit. 2 Hand Cart Use cart or similar device to move unit. 3 Line Disconnect Device Locate unit near correct input power supply. Special installation may be required where gasoline or volatile liquids are present . see NEC Article 511 or CEC Section 20. 24 in (610 mm) 17 in (432 mm) 12-1/2 in (318 mm) Movement 2 Do not move or operate unit where it could tip. Location 3 Dimensions And Weight 18 in (460 mm) 18 in (460 mm) 95 lb (43 kg) w/Torch 1 1 A complete Parts List is available at OM-201 872 Page 13 4-5. Connecting Work Clamp and Gas/Air Supply 1 Work Clamp 2 Workpiece Connect work clamp to a clean, paint-free location on workpiece, as close to cutting area as possible. Use only clean, dry air with 90 to 120 psi (621 to 827 kPa) pressure @ 9.2 CFM (260L/min) minimum. 3 Gas/Air Filter Inlet Opening 4 Hose Hose must have a minimum inside diameter of 3/8 in (9.5 mm). 5 Teflon Tape Obtain hose with 1/4 NPT righthand thread fitting. Wrap threads with teflon tape (optional) or apply pipe sealant, and install fitting in opening. Route hose to gas/air supply. Adjust gas/air pressure according to Section 5-2. Tools Needed: 9/16 in 3 4 Ref. 803 640-A / Ref. 192 441 / Ref. 804 026-A Rear of Unit 5 1 2 From Gas/Air Supply AIR/N2 90-120 psi @ 9.2 CFM (260 L/min) minimum 4-6. Connecting And Disconnecting Torch Turn off power source and disconnect input power. 1 Torch Connector 2 Quick Connect Collar 3 Nipple 4 Receptacle 5 Securing Pin To connect torch: Push torch connector onto receptacle and quick connect until collar secures nipple. Rotate securing pin to lock connector to unit. To disconnect torch: Rotate securing pin to unlock connector from unit. Push quick connect collar back towards unit to release nipple, and pull torch connector away from unit. 804 055-A 2 1 3 4 5 . A complete Parts List is available at 4-7. Electrical Service Guide . CAUTION: INCORRECT INPUT POWER can damage this welding power source. This welding power source requires a CONTINUOUS supply of 50 or 60 Hz (10%) power at +10% of 575V or .10% of 208V input voltage. Phase to ground voltage shall not exceed +10% of rated input voltage. Do not use a generator with automatic idle device (that idles engine when no load is sensed) to supply input power to this plasma power source. 60 Hz Three Phase Input Voltage 208 230 460 575 Input Amperes At Rated Output 55 49 24 19 Max Recommended Standard Fuse Rating In Amperes 1 Time-Delay 2 Normal Operating 3 60 80 60 70 30 35 20 30 Min Input Conductor Size In AWG 4 8 8 10 12 Max Recommended Input Conductor Length In Feet (Meters) 89 (27) 108 (33) 284 (87) 268 (82) Min Grounding Conductor Size In AWG 4 8 8 10 12 Reference: 2005 National Electrical Code (NEC) (including article 630) 1 Consult factory for circuit breaker applications. 2 “Time-Delay” fuses are UL class “RK5” . 3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and above). 4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table 310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements. 50 Hz Three Phase Input Voltage 400 Input Amperes At Rated Output 28 Max Recommended Standard Fuse Rating In Amperes 1 Time-Delay 2 Normal Operating 3 25 35 Min Input Conductor Size In AWG 4 12 Max Recommended Input Conductor Length In Feet (Meters) 155 (47) Min Grounding Conductor Size In AWG 4 12 Reference: 2005 National Electrical Code (NEC) (including article 630) 1 Consult factory for circuit breaker applications. 2 “Time-Delay” fuses are UL class “RK5” . 3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and above). 4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table 310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements. OM-201 872 Page 14 . A complete Parts List is available at 4-8. Extension Cord Data When calculating max. cord length, remember to include conductor length from line disconnect device to input power receptacle. NOTE Input Voltage Input Power Phase Hertz Fuse Size Or Circuit Breaker Rating Conductor Size Max. Cord Length 208 V 3 60 Time-Delay 2 60 A Normal Operating 3 80 A 8 AWG 89 ft (27 m) 230 V 3 60 Time-Delay 2 60 A Normal Operating 3 70 A 8 AWG 108 ft (33 m) 460 V 3 60 Time-Delay 2 30 A Normal Operating 3 35 A 10 AWG 284 ft (87 m) 575 V 3 60 Time-Delay 2 20 A Normal Operating 3 30 A 12 AWG 268 ft (82 m) 400 V 3 50 Time-Delay 2 25 A Normal Op...