Votos - 3, Puntuación media: 3.3 ( )

Fabricar: Lincoln Electric Tamaño del archivo: 1.57 mb Nombre del archivo: Idioma del manual:

2. Fully push the brass connector end of the gun cable into the outgoing side of the feeder wire drive. Secure the cable using the hand screw on the wire feeder. 3. Insert the control cable plug from the feeder trigger circuit into the mating socket on the gun cable feeder end handle. Connection to a Tweco #5 adapted feeder 1. Check that the drive roll(s) and feeder guide tubes are appropriate for the electrode size being used. 2. Fully push the brass connector end of the gun cable into the conductor block on the outgoing side of the feeder wire drive. Secure the cable using the hand screw or set screw in the conductor block. 3. Insert the round connector of the control cable into the mating connector on the front of the wire feeder. Connection to a Lincoln feeder for 3/32” diameter wire 1. Check that the drive roll(s) and feeder guide tubes are appropriate for the electrode size being used. 2. Fully push the brass connector end of the gun cable into the conductor block on the outgoing side of the feeder wire drive. Secure the cable using the hand screw or set screw in the conductor block. 3. Insert the round connector of the control cable into the mating connector on the front of the wire feeder. I The K126 Innershield Pro gun has been designed for use with Lincoln Innershield brand self-shielded cored wire electrodes. Refer to the appropriate Lincoln Process and Procedure Guidelines for the electrode used for information on recommended electrical and visible stick outs. out. When using an open arc process, it is necessary to use eye, head, and body protection. LECTRIC SHOCK can kil I Do not touch electrically live parts such as output terminals or inter nal wiring I Insulate yourself from the work and ground I Always wear dry insulating gloves ES AND GASES can be danger ous I Keep your head out of fumes I se ventilation or exhaust to remove fumes from breathing zone LDING SPARKS can cause firer explosion I Keep flammable material away ARC RAYS can burn I Wear eye, ear and body protection Only qualified personnel should operate this equipment 1. Check that the welding power source is on. 2. Position electrode over joint. End of the electrode should be slightly off the work. 3. Lower welding helmet, close gun trigger, and begin welding. Hold the gun so the contact tip to work distance gives the correct electrical stick out as required for the procedure being used. 4. To stop welding, release the gun trigger and then pull the gun away from the work after the arc goes Wire feeding problems can be avoided by observing the following gun handling procedures: 1. Do not kink or pull cable around sharp corners. 2. Keep the electrode cable as straight as possible when welding or loading electrode through cable. 3. Avoid wrapping excess cable around handle or front of wire feeder. 4. Do not allow dolly wheels or trucks to run over cables. 5. Keep cable clean by following maintenance instructions. 6. Use only clean, rust-free electrode. The Lincoln electrodes have proper surface lubrication. 7. Replace contact tip when the arc starts to become unstable or the contact tip end is fused or deformed. I Wire Feeder Data Kit No. for Gun Manufacturer Model 5/64” diameter or smaller wire 3/32” diameter wire Lincoln Electric LN-7, LN-8, & LN-9 series; LN-25 (0.052 max.); LN-742 K466-1 none LN-7, LN-8, & LN-9 series; LN-25 (1/16 and larger); LN-742 K466-8 K613-6 LF-72, LN-74 K466-10 none Series 10 feeders; LN-15; PF-10M; PF-15M K466-10 none Power MIG & Wirematic series feeders K466-6 none Tweco Adapted No. 2, 3, and 4 guns K466-2 none No. 5 guns K613-2 K613-2 Miller Intellimatic, Side Kick, D-51A, Porta-MIG, Millermatic 130, 300 & 35 S-42GL, S-52A & S-54A Swing Arc –Dual & Single, S-22, S-32S, 52D, 54D, 54E, 60 & 70 series K466-3 K613-3 Hobart Dualmatic 27/70, H3S, H4S, H6S Mega-Conds 27, 44, 45, 70, 70S K466-4 K613-4 2000 series; 17 Hefty K466-7 K613-5 ESAB Digamig, EH1, 5 & 11, SEH-4 & 5, SWM11 & 11B, 12, 13, 23, 24, 25, 26, 35, VAM2 K466-5 none I Wire Diameter Liner KPo 0.035 KP44-3545-15 0.045 KP44-3545-15 0.052 KP44-116-15 1/16 KP44-116-15 0.068 KP44-564-15 0.072 KP44-564-15 5/64 KP44-564-15 3/32 KP45H-332-15 K613-X Gun Connector Kit is Required for 3/32” wire. P Numbes Wire Diameter 10-piece pack 100-piece pack 0.035 KP2745-035R KP2745-035R-B100 0.045 KP2745-045R KP2745-045R-B100 0.052 KP2745-052R KP2745-052R-B100 1/16 KP2745-116R KP2745-116R-B100 0.068 KP2745-072R KP2745-072R-B100 0.072 KP2745-072R KP2745-072R-B100 5/64 KP2745-564R KP2745-564R-B100 3/32 KP2745-332R KP2745-332R-B100 Stainless Steel Jacketed P Numbr bend Angle Notes KP2906-62 62e No reverse bend KP2906-62R 62e With reverse bend KP2906-30R 30e With reverse bend KP2906-30R-L 30e With reverse bend, extended length KP2906-30 30e No reverse bend KP2906-30-L 30e No reverse bend, extended length Classic Varnished Jacketing KP Number bend Angle Notes KP2927-62R 62e No reverse bend KP2927-30R-L 30e With reverse bend P Numbr Desired ESOKP2907-1 1.5" or less KP1987-1...

Descargar ahora

Introduzca dos números de la imagen: