Parts Section -9 CHAINGUARD ASSEMBLY - FRONT CENTER ITEM PART NO. QTY. DESCRIPTION 1 00778190 1 DOUBLE CHAINGUARD, ASY, CTR LH 2 00778192 1 DOUBLE CHAINGUARD, ASY, CTR FRT 3 00778191 1 DOUBLE CHAINGUARD, ASY, CTR FRT RH 4 4526 7 FLANGE LOCKNUT 1/2 NC 5 02030700 7 HHCS 1/2-13UNC 1-1/4 PL5 FALCON 10 and 15 09-08 ©2008 Alamo Group Inc. Parts Section -10 CHAINGUARD ASSEMBLY - FRONT WING ITEM PART NO. QTY. DESCRIPTION 1 00778141 1 DOUBLE CHAINGUARD ASSY, FRONT WING 2 00002700 4 FLATWASHER 1/2 PL STD

It may include features and applications of the product. Advantage Lincoln This section highlights the key features and benefits of the product. Product Picture Detailed photo of Lincoln product. Processes Recommended arc welding processes for the product. Input & Output Icons See below for descriptions. Unit Includes/Key Options These sections lists options that are included or are the most popular options requested for each product. Literature Number Order number to request more inf

See the ACCESSORIES section for available options. 12. Electrode Connection (Positive) - For quick disconnect system using Twist-Mate™ cable plugs 13. Welding Parameter Display - LED’s show which mode or welding parameter is activated for adjustment. • If it is necessary to modify the welding parameters "Item 13": - Wait four seconds after the LED’s on the panel have gone out, the welding current LED will be lit. - Press the SETUP/Parameter push button "Item 4"; every time the push button i

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in applying these types of fabrication methods and service requirements. Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to for any updated infor

The eld rocess elector witch is used to set the desired weld mode. The Flextece 450 has 4 selectable welding modes: O This is a CC (constant current) weld mode used for the SMAW stick welding process. O This is a CC (constant current) weld mode used for the GTAW TIG welding process. O This is CV (constant voltage) weld mode used for welding the GMAW MIG welding process and the FCAW-GS, flux cored gas shielded welding process. nnershield O This is a CV (constant voltage) weld mode used for weldin

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B3 Engine Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B3.2 Cold Weather Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B3.2 Welder Operation . . . . . . . .

1. Low oil pressure (engine protection light lit). Check oil level (Consult engine service dealer). 2. High water temperature. Check engine cooling system. (engine protection light lit). 3. Faulty oil pressure switch. 4. Faulty water temperature switch. Contact authorized local Engine Service Shop. Engine shuts down while under a load. 1. High water temperature. Engine runs rough. 1. Dirty fuel or air filters may need cleaned/replaced. 2. Water in fuel. Engine will not shut off. 1. Fuel Shutdown

12 5C GROUNDING BOLT ON ENGINE BLOCK STUD ON ENGINE MOUNTING FOOT LEFT SIDE 1 42A 41A 232P GOLD SILVER SENSOR COIL HOLD COIL PULL SHUTDOWN SENSOR COIL SENSOR SWITCH FUEL LVL. OIL TEMP. SENSOR & SWITCH OUTPUT PANEL 262 GROUND STUD ON SOL. SOL. OIL PRESSURE SWITCH & SENSOR SWITCH WK 233 234 265 SENSE NEG EXC MOTOR STARTING 281 5R FRAME POS 242D 239 229 5N 236C 232 236A RUN STOP 232H 32 HIGH + 232C 242B GND-J SHOWN IN SWITCH SHOWN IN RUN/STOP "ALWAYS ON" POSITION 32 5J GND-J FUEL GND. STUD ON BOTTO

When power is cycled, this option is automatically reset to False. False = Voltage sensing is automatically determined by the selected weld mode and othermachine settings (default). True = Voltage sensing is forced to "studs". P.99 Show Test Modes? Most power sources contain weld modes used for calibration and test purposes. By default, the machine does not include test weld modes in the list of weld modes that are available to the operator. To manually select a test weld mode, set this option t