Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Press the VOL button to increase volume ; the green bar on the screen moves right. 3.5.2. Press the VOL button to decrease volume ; the green bar on the screen moves left. Display of minimum volume Display of maximum volume ......................... 3.6 AV/TV SELECTOR Press AV/TV button to change TV mode to AV mode when the set is in receiving (TV) mode. On the contrary, press it to change AV mode to TV mode when the set is in VIDEO mode. 3.7 TINT CONTROL Use this knob to control colour tone during reception of pictures when using the NTSC system. 5 4. REMOTE CONTROL OPERATION: REMOTE CONTROL UNIT : CHANNEL SELECTOR 1 ~ 9 : DIGITAL CHANNEL SELECTOR : STANDBYCH VOL : VOLUME CONTROL PPS : PERSONAL PREFERENCE SELECT 10/0 : CHANNEL 10 OR CHANNEL 0 SELECTOR (BRIGHTNESS, COLOUR) SYSTEM : COLOUR SYSTEM CONTROL : PICTURE/TIME ADJUSTMENT -/- -: DIGIT OR TWO DIGIT CHANNEL PICTURE : PICTURE CONTROL SELECT DSP : DISPLAY : PREVIOUS 4.1 INSTALLING BATTERIES: 4.1.1 Remove the battery cover of Remote Control Unit. 4.1.2 Insert two "AAA", 1.5V batteries, making sure the polarity ( + or - ) of the batteries matches the polarity marks inside the unit. 4.1.3 Close the battery cover NOTE: * When the Remote Control Unit is not used for a long time or the batteries are worn out, take out the batteries to prevent electrolyte leakage. * Take care not to drop, dampen, dissemble the Remote Control Unit. 4.2 STANDBY BUTTON Refer to 3.1. 6 4.3 CHANNEL SELECTION 4.3.1 Press CHANNEL SELECTOR ( ) the channel number will be increased or decreased and displayed in the upper right corner of the screen. 4.3.2 Use the DIGITAL CHANNEL SELECTOR button for direct channel selection. 1) 1~10 channel Method 1: Press -/---Press 2 2 Example: To select channel 2 (Display) Press -/--- -Press 10/0 To select channel 10 10 Method 2: Example: To select channel 2 Press -/--- -Press 10/0 10 Press 2 To select channel 10 Press -/--- -Press 1 1 Press 10/0 2) 11~99 channel To select channel 28 Press -/--- -Press 2 2 Press 8 3) 0 channel Press -/- Press 10/0 0 Press 8 7 4.3.3 PREVIOUS BUTTON Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous previous programme you watched was was on channel 15; then you can press the button to reach channel 15, press it again to return channel 6. 6 5 4.4 SOUND CONTROL 4.4.1 VOLUME CONTROL 4.4.1.1 Press the VOL button to increase volume; the green bar on the screen moves right. 4.4.1.2 Press the VOL button to decrease volume; the green bar on the screen moves left. 4.4.2 MUTE BUTTON When there is a phone call or a visitor, it can temporarily shut off the sound without affecting the picture. To resume normal, press the MUTE or VOLUME ( ) button. The previous volume will be displayed for 4 seconds. MUTE PRESS AGAIN VOLUME VOLUME l.............. llllllllll..... 4.5 PICTURE CONTROL 4.5.1 Press the PICTURE CONTROL button on the Remote Control Unit. The FUNCTION to be adjusted is selected in sequence as shown in the following chart at every press of the button. CONTRAST BRIGHTNESS COLOUR 4.5.2 Adjust the button to obtain satisfactory picture. ON SCREEN CAPTION DISPLAY Green Bar Moves DISPLAYFUNCTION Press button Press button Contrast CONTRAST Weak Strong Brightness BRIGHTNESS Dark Light Colour COLOUR Pale Deep 8 4.6 Making use of PPS button (personal preference select) Press the PPS button, the screen will display the following five mode progressively: Press PPS again Press PPS again Press PPS againPress PPS 1 2 5 The above five display modes corresponding analogue quantity is shown in the following chart: Analogue Display BRIGHTNESS COLOUR CONTRAST mode 1 lllllllllllllllllllllllllllllll lllllllllllllllllllllllllllllll lllllllllllllllllllllllllll 2 llllllllllllllllllllllllllllllll llllllllllllllllllllllllllll lllllllllllllllllllllllllll 3 llllllllllllllllllllllllllll llllllllllllllllllllllllllll lllllllllllllllllllllllllll 4 llllllllllllllllllllllllllll lllllllllllllllllllllllllll lllllllllllllllllllllllllll 5 lllllllllllllllllllllllllll lllllllllllllllllllllllllll lllllllllllllllllllllllllll 4.7 DISPLAY BUTTON (DSP) Press this button, the present channel number will be displayed on the screen. If the electronic clock is in operation, the channel position and time will be displayed together at the upper right corner of the screen. Press this button for second time, channel position and colour system will be displayed. Press this button for third time to cancel display. Press DSP Press DSP again Press DSP again 8 6 : 00 8 PAL 9 4.8 SLEEP BUTTON 4. 8. 1 Using SLEEP button allows you to have the appliance automatically turned off after a pre-determined time, and set the appliance to STAND BY mode. Decrease 10 minutes at every press SLEEP Press again SLEEP 90 (GREEN) SLEEP 0 (RED) SLEEP 10 (GREEN) 4. 8. 2 After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes...