Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Making use of this function can skip some unwanted channel, say 5, 11, next when you press CH button to select channel, 5, 11 channel will be skipped. 0 1 4 61012 * Press the channel direct select button can select the skipped channel. 3) AFT ON/OFF Making use of the AFT function can automatically fine tune the channel. Select and highlight AFT, pressing VOL button it toggles between ON and OFF. When in AFT ON, it can automatically fine tune the channel. In normal circumstances, please set AFT ON. When in the process of manual search, AFT is set "OFF" automatically. 4) Band Selection Press the CH button to highlight BAND. Press the VOL button to select band. The change sequence is VL VHU 9 5) SYS (sound system) This item is used to select sound system. Since this TV model’s RF sound system is B/G only, this item gets into ineffectiveness in sound system selection. 6) Auto - search (AUTO) Press CH button to highlight AUTO. Press VOL button the set will automatically search and store the active TV signals in your local area from lower band to higher band in the sequence of VL VH U with the green bar moving rightward. When a station is located, the set will store the signals with a channel number from 0. When all the signals are searched and stored, the TV returns to 0 channel automatically, auto-search is finished. * After auto-search, all programs colour system is set to AUTO and in AFT-ON mode. * During the process of auto-search, if , MENU or CH button is pressed, the searching is interrupted. Press VOL button the searching begins again. 7) SEARCH Making use of SEARCH function will store a TV program at a referred channel position. Select a channel number, when SEARCH is highlighted, press VOL button, the set begins to search for signals upward or downward from current channel. When a station is located, the searching stops and the program is stored into the referred channel position. Repeat the above step and store another program signals into another position. If two channels are same, the previous will be deleted. When the searching is finished, to store the program signals you should press the MENU button to exit the menu and the program signals are stored automatically. * When the tuning changing reaches the highest (lowest), the searching turns to next band’s lowest (highest) and continues searching. If the signals are not the signals you desire, you can press the VOL button again until the desired signals are searched. 8) Manual search (MANUAL) When some program’s picture or sound is not good, you can make use of this function to fine tune the tuning voltage. Press VOL button to highlight MANUAL. Press VOL successively, the set begins searching upward or downward. When the picture has obtained the optimum effect, release the button. To store the effect you should press the MENU button to exit the menu and the effect is stored automatically. 10 3. FUNCTION menu STD AUTO SYS 1 BLUE ON Making use of the FUNCTION menu can select BLUE ON/OFF and current channel’s colour and sound system. Press CH button to select item (the selected item is highlighted). Press MENU button to exit to the main menu. 1) STD (colour system) selection. In this TV model the colour system is automatically identified. In normal circumstances, please set colour system to AUTO. 2) SYS (sound system) selection. In this TV model this item is ineffective. (Refer to the NOTE on page 6) 3) BLUE ON/OFF selection. Select and highlight BLUE ON/OFF. Press VOL button to select ON or OFF. When "BLUE ON" is selected, blue background will appear on the screen automatically when no input signals, and the sound is mute. After 5 minutes the set will cut off automatically. Channel selection 1. Using direct select buttons 1) Single digital method ( 0~9 ). You can select any one of 0~9 channel position directly by pressing the number button accordingly. Press " 5 "Press "0" AUTO SYS 1 AUTO SYS 1 2) Two digital method (10~99). Press "-/--" button until the symbol "--" is displayed on the screen. In this mode you can choose any one of two digit channel by pressing the number buttons accordingly. For example, if you wish to receive channel 25, press "2" button, then press "5" button. 11 Press " 2 "Press "-/--" Press " 5 " 25 AUTO SYS 1 2 - Press " 2 "Press "-/--" Press " 5 " 25 AUTO SYS 1 2 - Two digit mode 2. Using CH button Press CH button, the channel number will be increased or decreased progressively. 3. Making use of button Press button to swap the currently viewed channel with the previous channel. 1 AUTO SYS 1 20 AUTO SYS 1 Press Picture and volume adjustment 1. Picture adjustment Press PIC button repeatedly, on-screen display will change in the sequence below Press VOL button to adjust the level. For example, to adjust brightness: PAL BRIGHTNESS CONTRAST COLOUR SHARPNESS NTSC BRIGHTNESS CONTRAST COLOUR TINT SHARPNESS l.......... Press " " Press " " BRIGHTNESS 0 Press "PIC" After 4 seconds lllllllllll BRIGHTNESS 63 llll....... BRIGHTNESS 30 (Not...