Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
(Refer to page 28.) . LC-XT1 Total lines The number of the total vertical lines. Adjust the number to match the image of your personal computer. Total dots The number of the total dots in one horizontal period. Adjust the number to match the image of your computer. Horizontal I Vertical Adjustment of the horizontal or vertical picture position. When the image is not centered on the screen, adjust each of those items. Clamp Adjustment of the clamp level. When the image has a dark bar(s), try this adjustment. Fine sync Adjust the picture as necessary to eliminate flicker from the display. Display area Adjustment of the area displayed with this projector. Select the resolution at the Display area dialog box, or adjust the number at the column of “H” or “V” to match the resolution of the image. Horizontal Scale I Vertical Scale Adjustment of the horizontal height or vertical width of the image. NOTE: The Display area, the Horiz. scale and the Vert. scale cannot be adjusted when “480p”, “S7Sp”, “HDTV72Op”, “HDTV1O35i” or “HDTV1O8Oi” is selected on the SYSTEM MENU (P28 and 29). . LC-XT1 NOTE: The Fine sync and the Total dots cannot be operated when the input signal is digital from DVI terminal or “RGB” is selected on the SYSTEM MENU (P28 and 29). The Progressive cannot be selected when the input signal is digital from DVI terminal or “480p”, “S7Sp” or “HDTV72Op” is selected on the SYSTEM MENU (P28 and . LC-XT1 ‘-‘C’’ The AUTO IMAGE function cannot be operated when the input signal is digital from DVI terminal or “RGB”, “480p”, ‘575p”, “HDTV72Op”, “HDTV1O35i” or “HDTV1O8Oi” is selected on the SYSTEM SELECT menu. Press the AUTO IMAGE button on the Side Control or on the Remote Control Unit to automatically adjust Fine sync., Total dots and Screen position for most computers. It will take about 10 seconds. NOTE:Some computers may not be fully adjusted with the “Auto Image Function”. In that case, use the “Picture Image” and/or “Picture Position” adjustments (P32, 33) to make fine-adjust then after the “Auto Image Function” isexecuted. . LC-XT1 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button. Another dialog box PICTURE SCREEN Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT button. NOTE • The True and the Digital Zoom cannot be operated when “RGB”, “480p”, “575p”, “HDTV720p”, “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P28 and 29). • This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connection the projector. • The image data in other than XGA (1024 X 768) is modified to fit the screen size in the initial mode. • The normal “Panning Operation” may not function properly if the computer system prepared with the “PC Adjust” is used. . LC-XT1 When connecting to those equipment, select the type of Input source in INPUT SOURCE Menu. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select INPUT SOURCE and press the SELECT button. Another dialog box INPUT SOURCE Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “Y, Pb/Cb, Pr/Cr” and then press the SELECT button. Video When connect the composite video output from the video equipment to the VIDEO/Y jack, select “Video” in VIDEO SOURCE Menu. When connect the separate Y/C video output from the video equipment to the VIDEO/Y and C jacks, select “Y/C” in VIDEO SOURCE Menu. S-Video When connect the S-Video output from the video equipment to the S-Video jack, select “S-Video” in VIDEO SOURCE Menu. . LC-XT1 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box VIDEO SYSTEM Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will . LC-XT1 . LC-XT1 . 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SETTING and press the SELECT button. Another dialog box SETTING Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to set, and then press the SELECT button to set it (For example “On” or “Off”). Power management This function turns the Projection Lamp off when the projector detects signal interruption and the projector is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.) Power Management function operates to turn the Projection Lamp off when the input signal is interrupted and the projector is not operated over 5 minutes. This function operates as follows; 1. When the signal is interrupted, “No signal” and the counting d...
Otros modelos de este manual:TV - LC-XT1 (2.57 mb)