Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
The value will vary depending on the installation conditions, etc.) ITEM ASCII HEX VALUE KEYSTONE(vertical) KS 4Bh 53h +20 - -15 +20 - -5 (for WD500U-ST) How to set the value Use the ASCII or HEX code as shown below to set the value. ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9' HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 7) Mute commands (Not executable in stand-by mode. When the mute commands are sent while the splash screen is being displayed, the splash screen is only canceled.) The mute commands are used for the mute setting of this projector with the 0 (30h) and 1 (31h). ITEM ASCII HEX VALUE MUTE MUTE 4Dh 55h 54h 45h 0 (OFF), 1 (ON) 8) Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash screen is being displayed, the splash screen is only canceled.) Some remote control operations can be achieved by the remote command codes.The remote commands have no data codes. Button's name on remote ASCII HEX + VOLUME r06 72h 30h 36h – VOLUME r07 72h 30h 37h KEYSTONE r43 72h 34h 33h MAGNIFY r02 72h 30h 32h AV MUTE ra6 72h 61h 36h ^ r53 72h 35h 33h Ў r2b 72h 32h 62h t r4f 72h 34h 66h s r59 72h 35h 39h MENU r54 72h 35h 34h ENTER r10 72h 31h 30h AUTO POSITION r09 72h 30h 39h FREEZE ra4 72h 61h 34h ASPECT re2 72h 65h 32h [Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. Status code from the projector Description 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' Command operating the same as the MENU button 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' Command receipt confirmation (Command echo back) 9) Password lock commands The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password lock is enabled or disabled successfully, the projector sends a return command comprising the data code, password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command with “0” at the end. There is no reconfirmation of the password. The password input command is for enabling projection of image when password lock has been set to DISPLAY INPUT. The password input command is sent with a 4 to 8digit password comprised of any figures 1 to 4 at the end. ITEM ASCII HEX VALUE Password lock enabling/disabling PSLOCK 50h 53h 4Ch 4Fh 43h 4Bh 0**** (Disabling), 1**** (DISPLAY INPUT), 2**** (MENU ACCESS), 3**** (SPLASH ID SCREEN) Password input PASS 50h 41h 53h 53h **** **** is a 4 to 8-digit password comprised of any figures 1 to 4. 3 [Example] When enabling the password lock of DISPLAY INPUT (in the case that the password is 123412): Sending commands from the PC, etc. Status code from the projector Description 30 30 50 53 4C 4F 43 4B 31 31 32 33 34 31 32 0D '0' '0' 'P' 'S' 'L' 'O' 'C' 'K' '1' '1' '2' '3' '4' '1' '2' ' ' Command for enabling the password lock of DISPLAY INPUT 30 30 50 53 4C 4F 43 4B 31 31 32 33 34 31 32 31 0D '0' '0' 'P' 'S' 'L' 'O' 'C' 'K' '1' '1' '2' '3' '4' '1' '2' '1' ' ' Response informing that the projector succeeded in enabling the password lock of DISPLAY INPUT 10) Reading command diagram The projectors operating status, such as POWER-ON/OFF and the currently selected input terminal, etc. can be monitored. ASCII HEX Function Data (Receive) Function Data (Receive) POWER ON vP 1 76h 50h 31h POWER OFF vP 0 76h 50h 30h INPUT COMPUTER 1 vI r1 76h 49h 72h 31h INPUT COMPUTER 2 vI r2 76h 49h 72h 32h INPUT VIDEO vI v1 76h 49h 76h 31h INPUT S-VIDEO vI v2 76h 49h 76h 32h INPUT DVI vI d1 76h 49h 64h 31h POWER ON/OFF IMPOSSIBLE vPK 0 76h 50h 4Bh 30h POWER ON/OFF POSSIBLE vPK 1 76h 50h 4Bh 31h NO SIGNAL SUPPLIED vSM 0 76h 53h 4Dh 30h SIGNAL SUPPLIED vSM 1 76h 53h 4Dh 31h LAMP TIME (LOW) vLE hhhhmm 76h 4Ch 45h – "hhhh" and "mm" represent hours and minutes respectively. The PC sends the command without attaching the data code to it. On the other hand, the projector attaches to the received command its current operating status as the data code and send it back to the PC. [Example] When checking the currently selected input terminal (when the INPUT VIDEO is being selected): Sending commands from the PC, etc. Status code from the projector Description 30 30 76 49 0D '0' '0' 'v' 'I' ' ' Command for checking the input terminal 30 30 76 49 76 31 0D '0' '0' 'v' 'I' 'v' '1' ' ' Check result ( VIDEO) 11) Menu setting commands (Not executable in stand-by mode. Possible only to read during muting.) The menu setting commands are used for the menu setting of this projector. If the personal computer sends the command without attaching the data code, the projector attaches to the received command its current setting value as the data code and send it back to the PC. ITEM ASCII HEX VALUE COLOR ENHANCER CE 43h 45h 0 (AUTO), 1 (PRESENTATION), 2 (STANDARD), 3 (THEATER), 4 (USER) COLOR ENHANCERUSER- GAMM...
Otros modelos de este manual:TV - WD510U-G (475.11 kb)
TV - WD510U-G (475.11 kb)