Votos - 5, Puntuación media: 4.4 ( )

Fabricar: Mitsubishi Electronics Tamaño del archivo: 3.74 mb Nombre del archivo: 9b54b4d0-5e08-5684-8d70-6325da8fa71e.pdf Idioma del manual:

24. PIP CH: Scrolls up or down through memorized channels for PIP or POP. 25. HOME: Exits TV on-screen menus and return to TV viewing. 26. INFO: Displays on-screen summary of the current device used and any broadcast information available (including current V-Chip information). See Appendix D for details. 27. REC/CONNECT: Record with a VCR, setup recordings for DVCR or IEEE 1394 devices. Initiate IEEE 1394 peer-to-peer connections. Setup recordings while in ChannelView. 28. STOP: Stops a VCR, DVD or A/V Disc. 29. PAUSE: When no PIP or POP image is displayed, pauses the main TV Picture. When PIP or POP image is visible, pauses that image. Pauses a VCR, DVD or A/V Disc. 30. REW/REV: Rewind or reverse search with a VCR, reverse scan with a DVD or A/V Disc. 31. PLAY: Play a VCR, DVD or A/V Disc. 32. FF/FWD: Fast forward or forward search with a VCR or fast play a DVD. Remote Control Functions:Operation, Care, Sleep Timer POWERHOMEPAUSERECFF/FWDREW/REVPLAYSTOP369QVVOLUMEINFOEXCHENTERTVMENUDEVICEMENUV-CHIPFORMATPIPCH17SQV4DEVICESLEEPVIDEOAUDIOMUTE2580CHANNELADJUSTPIP/POPPIPDEVICECANCELTVAUDIOCABLE/DBS/DTVDVDVCRGUIDESUBCONNECT 1 2 3 9 10 4 5 11 12 6 7 8 13 16 15 14 17 18 19 22 20 24 25 21 23 26 27 29 28 30 32 31 Hint: If the remote is in the TV layer and will not function, press POWER and OOO (or POWER and 935 if NetCommand® is setup) to reset the remote. Figure 1. Remote Control Overview Operation Figure 2 Installing the Batteries: 1. Remove the remote control’s back cover by gently pressing the ribbed tab in the direction of the arrow and sliding off the cover. 2. Load the batteries, making sure the polarities (+) and (-) are correct. For best results, insert the negative (-) side first. Care For Best Results from the Remote Control: • Be within 20 feet of the equipment. • Do not press two or more buttons at the same time unless instructed to do so. • Do not allow unit to get wet or become heated. • Avoid dropping on hard surfaces. • Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth. • Do not mix new and old batteries. • Do not heat, take apart or throw batteries into fire. • Use only AAA alkaline batteries. Sleep Timer Setting the Sleep Timer: 1. Press SLEEP on the remote control. 2. Each press of SLEEP increases the time displayed by 30 minutes, until the maximum value of 120 minutes is reached. 3. After 5 seconds of inactivity, the message will disappear. 4. Press SLEEP to view the remaining time before the timer turns the TV off. Canceling the Sleep Timer: 1. Press SLEEP to display the on-screen message. 2. Press SLEEP repeatedly until OFF is displayed. Note: After 5 seconds of inactivity, the message box disappears. .................................................... Figure 2. Operation: Installing the Batteries NetCommand® On-Screen Buttons To use the TV’s NetCommand feature, the manufacturers of the devices that are connected to the television need to be defined during the Initial NetCommand setup. The TV can also learn the remote control IR code signals for most non-defined devices. During the initial setup, every available device is assigned to a specific input of the TV and/or A/V Receiver. Changes to the inputs or names are made through the Edit NetCommand screens. The buttons described below will help you navigate the screens. On your remote control, the ADJUST and buttons allow you to navigate left and right to different selections on the screen. The ADJUST and buttons allow you to: • Change the radio button • Change current text box selection • Navigate up and down on the screen The ENTER button allows you to: • Confirm the selected character when naming a device • Add or delete check marks in check boxes • Select on-screen buttons to change screens Textbox Press ADJUST or to make a selection. Checkbox Checkmarks indicate the item or input is added or turned On. Press ENTER when the Checkbox is highlighted to add or delete a checkmark. When viewing the Review screen, a Checkbox reflects which devices are turned On or Off, or connected to the TV. Control Buttons Much like the software on your computer, you will use graphic buttons to navigate through the NetCommand Setup screen. Highlight the button and press ENTER to select the function. Button Use the Next> button to navigate forward to the next screen. Cancel Button The Cancel button will stop any changes you are currently making without saving them into memory. When you select the Cancel button, NetCommand will prompt you to confirm that you want to cancel the changes you are currently making. If you select Cancel during Initial Setup. You can setup NetCommand later by selecting the NetCommand menu, then choosing Initial. Radio Button The setting changes when one of the choices is highlighted. 3D Graphical Menu System Your TV also has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on- screen information fo...

Descargar ahora

Introduzca dos números de la imagen: