Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Important! – Please Read This Manual Before Installing! Congratulations on your purchase of a Voyager AOM701 LCD Observation Monitor. With proper installation and use, your AOM701 is designed to provide you with years of trouble-free operation. This manual contains important information required to properly install and operate the unit. Please read this manual thoroughly before beginning. All Voyager Observation products are strictly intended to be installed as a supplement aid to standard rear-view mirror systems that may already exist in your vehicle. Voyager observation products are not intended for use as substitutes for rear-view mirror devices, or for any other standard motor vehicle equipment required to be installed on vehicles by law. While Voyager observation products contribute to improving the vehicle operator’s field of view, these products are no substitute for proper defensive driving techniques and observance of traffic laws and motor vehicle safety regulations. Warnings! Camera-Monitor Warning 1. Camera/monitor system aids in the use of, but does not replace vehicle side/ rear-view mirrors. 2. Objects in camera/monitor view are closer than they appear. When backing up, proceed cautiously and be prepared to stop. Installation Location It is unlawful in most jurisdictions for a person to drive a motor vehicle equipped with a television viewer or screen located at any point forward of the back of the driver’s seat or in any location that is visible, directly or indirectly, to the driver while operating the vehicle. The AOM701 product is designed to be used primarily as a rear observation device in conjunction with closed circuit cameras. In any installations where the AOM701 is used to display television broadcasts or recorded video playback, installation location must adhere to local laws and regulations. Tampering To prevent electrical shock, DO NOT OPEN THE MONITOR CASE. There are potentially harmful voltages inside the monitor. There are no user serviceable parts inside. If evidence of tampering is detected, the warranty will be considered void. Moisture Your Voyager AOM701 was designed to be water-resistant. While it will with stand short periods of exposure to moisture, this product does contain sensitive electronic components and exposure to moisture should be limited by the user / installer. This product is not designed for applications where constant exposure to moisture or immersion can be encountered. This unit should NEVER be cleaned with a power washer or used where direct power washer spray may be encountered. PACKING CONTENTS: DISTANCE MARKER STICKER QTY.1 CONNECTION CABLE QTY.1 90 DAY/ 12 MONTH LIMITED WARRANTY WARRANTY CARD QTY. 1 LCD MONITOR QTY. 1 SUN SHIELD QTY. 1 5’ INTERMEDIATE HARNESS QTY. 1 #10 X 5/16” PHP THREAD FORMING BLACK SCREW (HARDWARE BAG) QTY. 4 1 • 1 • 2 • 2 • 3 • 3 • 4 • 4 • STOP STOP • • • • • • • • • • • • 4” BLACK WIRE TIE QTY. 4 3 POWER HARNESS QTY. 1 GND TRIGGER (+12V) STANDBY TRIGGER (+12V) AUDIO ACC (+12V) AV1 AV2 CONTROLS AND OPERATION A B – + 1 234 5 1. Power/Stand-By Button The Power / Stand-by Button has two possible operations modes. a. Manual mode - Turned on manual by the user by pressing the Power #1 button. b. Stand-by mode - Turned on by a stand by trigger wire generally connected to the vehicles 12V reverse backup lights. Manual Mode wiring - For manual mode operation, the AOM701 should be wired as follows: ACC (+12V) Red wire should be connected to the vehicles accessory feed. GND - ground wire should be connected to chassis ground. Standby Mode wiring - For Standby mode operation, the AOM701 should be wired as follows: ACC (+12V) Red wire should be connected to the vehicles accessory feed. GND - ground wire should be connected to chassis ground. Standby / Reverse trigger blue wire should be connected to the reverse feed of the vehicles backup lighting system. The power button #1 features dual illumination. It will be brighly lit when the unit is turned on and will be dimly lit when the unit is turned off. When the unit is turned on all other buttons will be illuminated. When off only the Power button will be lit. * Note: Please note that when the unit is in the standby mode, trigger wire is triggered, the Power button #1 will not function. A B A B – + 2. A/B Input Select Button This control toggles the active display image back and forth between AV1 and AV2 inputs. AV1 is the default source for the Blue Standby trigger wire. 3. Day/Night Mode Button This control toggles the unit between “Day” and “Night” LCD illumination modes. In the “Day” mode, the LCD backlight intensity is at maximum. In “Night” mode, the LCD backlight is dimmed to a preset level that is more suitable for low light operation. 4. Picture Adjustment Menu Button This control accesses an On-Screen-Display (OSD) menu for four LCD picture adjustments (Brightness, Contrast, Color, and Tint). The first depress of the button accesses the “Brightness” adjustment. The Volume +/- ...