Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
This ma y cause damage to the projector. I n st a l l a t i o n Turning on the Projector POWER Remove the lens cover. Connect the projector’s power cable with the projector, and insert the power cable into a wall socket. Turn on the AC power switch of the projector. The power indicator lights green and slowflashing. Projector works in standby mode. Press the power button to turn on the projector. The power LED begins to green and lamp LED begins to red, and the projector will be lamped on. Installation Turning on the Projector WARNING If no image are projected, change the input signal. POWER LAMP A KEYSTONE INPUT BLANK When using a laptop or a PC with an in built monitor, select external video output on the computer. Installation Connecting PC to the Projector To connect Computer cable (RGB). Computer 1 and Computer 2 To Computer monitor port Computer cable How to Connect Desktop PC Before starting, make sure that the projector and computers are both turned off. 1. Connect the computer cable. Connect either end of the computer cable to the projector’s Computer in 1 or Computer in 2 Disconnect the monitor cable from the computer and connect the other end of the terminal where the monitor cable is disconnected from the computer. If needed, connect the monitor cable of the computer monitor to the projector’s Monitor Out. Tighten the screw on all connectors. 2. Connect the audio cable if necessary. Connect one end of the audio cable to the Audio in jack on the projector. Connect the other end of the audio cable to the audio output port on the computer. VGA Desktop PC How to Connect Laptop PC Before beginning, make sure that the projector and computers are both turned off. 1. Connect the computer cable. Connect either end of the computer cable to the projector’s Computer in 1. Connect the other end of the project cable to the monitor out connection on the laptop. Tighten the all connectors. 2. Connect the audio cable if necessary. Connect one end of the audio cable to the Audio in jack on the projector. Connect the other end of the audio cable to the audio output port on the laptop PC. Laptop PC How to Connect Connecting Video to the Projector 1. Connect to a video source The Projector can receive compos ite AV ,YPbPr and S-Video. Connect RCA plug at projector and video source ( like DVD player) for video signal. Please contact with your dealer for optional cable. 2. Connect RCA plug ( white and red) to audio source ( like DVD player) and connect the phone jack to projector for audio signal. How to Connect 3. Connect YPbPr plug at projector computer in 2 port and video source ( like DVD player) for video signal. 4. For S-Video, using S-Video ca ble connect to projector and video source for video signal. Basic Operation Turning on the Projector -Procedure 1. Check the power is turned off for the projector and all components connected to the projector. 2. Remove the lens cover. 3. Connect the power cord to the projector. 4. Turn on the power switch. 5. Press the POWER button on the control panel or on the remote control. 21 5 3 KEYSTONE INPUT 4BLANK A Basic Operation Turnin g on the Proj ector -Procedure 6. The power indicator will flash green. 7. Press the Input button on the control panel or on the remote control to select the appropriate source. 8. Rotate the zoom ring to adjust the screen size. 9. Rotate the focus ring to adjust the focus. 6 POWER LAMP 9 8 6 KEYSTONE INPUT BLANK Basic Operation Turnin g off the Proj ector -Procedure 1. Press the power button on the projector or remote control. The power off confirmation message appears . 2. Press the power button again and the projector will enter cool-down mode. The lamp shuts off, the lamp indicator flashes red, and the fans continue to run for approximately two minutes. During the cool down sequence the projector will not respond to any control panel or remote control buttons. Do not set the power switch to off or unplu g the projector during the cool-down sequence. Not allowing C A U T I O N the lamp to cool properly will greatly reduce the life of the lamp. 3. After the cool-down sequence is completed the fans will shut off and the lamp indicator will stop flashing. The projector is now in standby mode and can be turned back on with the remote control or control panel. If the projector will not be used for an extended period, set the power switch to off and disconnect the power cord. Basic Operation Adjusting the Screen Image 1. Adjusting the image size Rotate the Zoom Ring to adjust the image. 2. Adjusting the image height Extend or retract the front adjustable foot to adjust the height of the image. 3. Correcting Keystone Distortion . Press the Keystone button on the control panel. . Keystone correction mess age will be appeared. . Press ”Left/Right” button to correct Keystone distortion. POWER LAMP KEYSTONE INPUT BLANK Press ”Left button” to Press ”Right button” to correct keystone distortion. correct keystone distortion. Fu n ct i o n s o f M e n u ( ...
Otros modelos de este manual:TV - LC-XWP2000 (14.71 mb)