Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
It reduces disturbance on old, worn video cassettes, and emphasises the detail on very good quality cassettes. Simple programming system for TV-VIDEO Combis. Makes programming as easy as making a telephone call. Simply enter the programme code which you will find in your listings magazine. The precision tape drive from Philips with rewind times of 100 seconds (E180) and automatic tape length recognition. We guarantee that your TV-VIDEO Combi will switch to the new millennium with no problems whatsoever. 1. CONNECTING YOUR TV-VIDEO COMBI Important for the United Kingdom This apparatus is fitted with an approved moulded 13 Amp plug. To change a fuse in this type of plug proceed as follows: a Remove fuse cover and fuse. b Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved type. c Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. DNote: * The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere. How to connect a plug: The wires in the mains lead are coloured in accordance with the following code: BLUE -’NEUTRAL’ (’N’) BROWN -’LIVE’ (’L’) d The BLUE wire must be connected to the terminal which is marked with the letter ’N’ or coloured BLACK. e The BROWN wire must be connected to the terminal which is marked with the letter ’L’ or coloured RED. f Do not connect either wires to the earth terminal in the plug which is marked with the letter ’E’ or by the safety earth symbol \or coloured green or green-and-yellow. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead -not simply over the two wires. Connecting the cables a Insert the aerial plug into the 2 socket. b Insert the plug of the mains cable into the wall socket. c If the little red light at the front of the set is not alight, please switch on the set. The power switch 8 is located on the left side panel of the set. Connecting a decoder or other equipment You can also connect additional equipment to the EXT.1 socket. For instance, a satellite receiver, decoder or camcorder. 2. INSTALLING YOUR TV-VIDEO COMBI Initial installation a Open up the battery compartment of your remote control and place the batteries in it as shown in the picture. b Close the battery compartment. c If you have connected the aerial to the TV-VIDEO Combi, press the OK button. ’Automatic TV channel search’ starts. This picture will appear on the screen: Searching... CHANNELS FOUND: //////,,,,,,,,,,,,,,,,,,,,, Wait until all TV channels have been found. This can take several minutes. DIf you have connected a decoder, you must install it as described in the next section. DIf you have connected a satellite receiver, please read the section ’satellite receiver’. Allocating a decoder Some TV stations will send coded TV channels, that you can only watch when you use a decoder. You can connect such a decoder (descrambler) to your TV-VIDEO Combi. With the following function, the connected decoder will automatically be activated for the TV programme you want to watch. a Choose the TV channel on which you wish to use the decoder with the qSC or DSr buttons on the TV-VIDEO Combi or the number buttons 0-9 on the remote control. b Press the MENU button on the remote control. The main menu will appear. c Select the line ’Installation’ with the AP q or P rB button and confirm with the qSC button. d Select the line ’Manual store’ with the AP q or P rB button and confirm with the qSC button. e Select the line ’Decoder’ with the AP q or P rB button. MANUAL STORE Channel/Frequency FREQU. Search 125 Fine tuning (,,,,,,n=,,,,,,$ Name edit xxx Programme number P01 Decoder OFF a Exit: « press MENU f Select function ’ON’ with the DSr or qSC button. When you select ’OFF’, the function will be switched off. g Confirm with the OK button. h To end, press the MENU button. Your decoder has now been allocated to this TV channel. Manual TV channel search In certain cases the ’Automatic TV channel search’ may not be able to find all of the TV channels (e.g. coded TV channels). In that case, use this manual method to set the channels. a Press the MENU button on the remote control. The main menu will appear. b Select the line ’Installation’ with the AP q or P rB button and confirm with the qSC button. c Select the line ’Manual store’ with the AP q or P rB button and confirm with the qSC button. MANUAL STORE Channel/Frequency FREQU. Search 125 Fine tuning (,,,,,,n=,,,,,,$ Name edit xxx Programme number P01 Decoder OFF a Exit: « press MENU d In the line ’Channel/Frequency’, select the display for: ’FREQU.’: frequency ’CCH’ : channel ’SCH’ : special channel e If you know the frequency or channel of the desired TV channel, you can enter the ...
Otros modelos de este manual:TV - 14PV327/05B (726.55 kb)