Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Your serial number is located under the name plate label on the right side of your MultiSync GT2000/GT2000R . Record it here: WARNING TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED NEC SERVICE PERSONNEL. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. DOC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. 3. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. Important Safeguards These safety instructions are to ensure the long life of your LCD projector and to prevent fire and shock. Please read them carefully and heed all warnings. Installation 1. For best results, use your LCD projector in a darkened room. 2. Place the projector on a flat level surface in a dry area away from dust and moisture. 3. Do not place your LCD projector in direct sunlight, near heaters or heat radiating appliances. 4. Exposure to direct sunlight, smoke or steam can harm internal components. 5. Handle your LCD projector carefully. Dropping or jarring can damage internal components. 6. Do not place heavy objects on top of the LCD projector. 7. If installing the LCD projector on the ceiling: a. The ceiling must be strong enough to support the LCD projector and the installation must be in accordance with any local building codes. b. The LCD projector must be installed by qualified NEC service personnel. Power Supply 1. The LCD projector is designed to operate on a power supply of 100120 or 220-240 V 50/60 Hz AC. Ensure that your power supply fits this requirement before attempting to use your LCD projector. 2. Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire. 3. If the LCD projector is not to be used for an extended period of time, disconnect the plug from the power outlet. Three types of power cable are supplied with this LCD projector: three- pin type for Japan, U. S. A. and Canada. Two-pin type for Germany. For Japan For Germany For North America (black) (gray) RF Interference WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Technologies in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit. This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems. E-2 Cleaning 1. Unplug the LCD projector before cleaning. 2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner. 3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens. 4. Clean the air filter with a vacuum cleaner after every 100 hours of operation. a. Clean the outside of the filter with a vacuum cleaner. b. Do not use water or any other liquid to clean the air filter. c. Do not operate your LCD projector without the air filter. Lamp Replacement • Perform lamp replacement in accordance with the instructions on page E-73. • Be sure to replace the lamp when the Status light comes on. If you continue to use the lamp after 2000 hours of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replacement. • Allow a minimum of ONE minute to elapse between turning the lamp off and on. High vo...
Otros modelos de este manual:TV - MultiSync GT2000, GT2000R (1.08 mb)