Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Do not fit to any surface other than a vertical wall. ..To ensure correct plasma TV performance and prevent trouble, do not fit at any of the following locations. • Near sprinklers or fire/smoke detectors • Where there is a risk of exposure to vibration or impact • Near high-voltage wires or dynamic power supplies • Near sources of magnetism, heat, water vapor or soot • Locations exposed to air blown from heating equipment • Where droplets of condensation from an air conditioner or other unit may form. ..Fit using techniques suited to the structure and materials of the fitting location. ..Use commercially available screws with a nominal diameter of 6 mm (0.2 inches) that are suited to the wall material (wood, steel frame, concrete etc.) you are fitting the bracket to. ..For the TV power supply plug, use a power supply outlet that can be reached easily. ..Ensure good air flow so that the equipment ambient temperature does not exceed 40 °C (104 °F). Failure to do this may cause heat to build up inside the plasma TV, resulting in malfunction. ..Spread a soft blanket or cloth over the floor so that the plasma TV and floor will not be marked or scratched during the assembly and installation work. ..When screwing down the parts, ensure that the screws are neither insufficiently tightened nor over tightened. ..Take sufficient care to ensure safety around you when performing the assembly and installation work or while moving about during the course of the work. ..Do not install the Plasma TV underneath ceiling lamps (spotlights, halogen lamps, etc.). Otherwise, the cabinet may be bent or damaged by high heat. [Never use any other method than specified to Fitting procedure install.] 1. Assembling the wall- English hanging bracket 1. Remove the screws for securing the bracket base left .. and right .. fittings. 2. Lay the base upper and lower fittings . and the bracket base left and right fittings .. and .. as shown in the figure. 3. Fit the tabs of the bracket base left and right fittings into the cutouts of the base upper and lower fittings above, and secure them using the two screws .. used to assemble the bracket. (Tightening torque: 1.2 to 1.5 N•m) 4. Open slightly the bottom of the bracket base left and right fittings, and fit their tabs into the cutouts of the base upper and lower fittings, and secure them using the two screws .. used to assemble the bracket. (Tightening torque: 1.2 to 1.5 N•m) 5. Tighten the screws for securing the bracket base left .. and right .. fittings which were loosen in step 1. Bracket base right fitting .. Base upper and lower fittings .. Base upper and lower fittings .. Tab Cutout Bracket base left fitting.. M5x10 screws for assembling the fixture .. Screw for securing the bracket base fitting Inside : 46-inch model Outside : 50 or 54-inch model Note • Please hold the bracket base left and right fittings as you work with the assembled wall hanging bracket. Holding the base upper and lower fittings might deform this unit. Unit: mm (inches) 2. Checking the strength of the 600 (23.6) installation location 1. The wall-hanging bracket weighs approximately 2.3 kg (5.1 lbs). Refer to the instruction manual of the plasma TV, and check the weight of the plasma TV unit which will be fitted into the wall-hanging bracket. 2. Refer to the outline drawing of the wall-hanging bracket shown on the right, and check the wall strength at the six installation positions shown. If the strength at any of these positions is lacking, provide sufficient reinforcement. Notes • There are five pre-drilled mounting holes at the top and another five at the bottom of the wall-hanging bracket. Use the spare holes provided if wood or some other material is used for the wall and a sufficient level of mounting strength cannot be ensured by anchoring the fixture at the six positions shown on the right. 440 (17.3) 80 (3.1) 80 (3.1) 516 (20.3) 42 (1.7) 59.5(2.3) 17.5(0.7) 325(12.8) (1.7) Wall mounting holes (at 6 points) Use the screws without fail to anchor the fixture. However, bear in mind that, depending on which materials the mounting surface is made of, cracks may form on the surface if the screws are used at positions which are too close together. • Mount or place only a plasma TV on the fixture: Do not mount or place any other product. • For details on the dimensions applying when the plasma TV is mounted, refer to the outline drawing (See back cover). 3. Installing the wall-hanging bracket on the wall English Notes In the case of the 46-inch model, limit • If it is necessary to embed bolts or nuts in the wall prior to the extent to which the screws and bolts installing the wall-hanging bracket because the wall is made protrude to within 5 mm (0.2 inches). of concrete, for instance, locate the positions of the holes by putting the actual wall-hanging bracket in place on the wall or by calculating the hole positions from the outline drawing, and then embed bolts and nuts with a nominal diameter of 6 mm (0.2 inches...
Otros modelos de este manual:TV - TY-WK5P1SW (308.01 kb)