Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
11 CH and CH buttons (CHANNEL) Press to change channels or to select features on the menu. 12 POWER button Press to turn the TV/VCR on or off. LEARNING ABOUT YOUR NEW TV/VCR L EARNING ABOUT Y OUR N EW TV/VCR Understanding the Controls, continued Rear Panel 1 VHF antenna mount VHF rod antenna mount. See page 12. 2 Antenna terminal Use this terminal (VHF/UHF IN FROM ANT) to connect the TV/VCR to a 75-ohm outdoor antenna or cable system. See page 12. CHAPTER ONE: LEARNING ABOUT YOUR NEW TV/VCR LEARNING ABOUT YOUR NEW TV/VCR Understanding the Controls, continued Remote Control Use the remote control within 33 feet (10 meters) of the TV/VCR and point it directly at the TV/VCR. 1 POWER Press to turn the TV/VCR on and off. 2 Number buttons Press to select specific channels. 3 +100 Press to select channels over 100. 4 REW (rewind) Press to rewind a tape. 5 STOP Press to stop a tape. 6 PLAY Press to play a tape. 7 FF (fast forward) Press to fast forward a tape. 8 CLEAR Press to correct programming errors, clear programs, or reset the tape counter. 9 –VOL and VOL+ (volume) Press – VOL to decrease or VOL+ to increase the volume. 10 CH and CH (channel) Press CH or CH to change channels. Also used with the menu system. 11 MENU Press to display the on- screen menu. 12 DISPLAY Press to show on-screen displays. 13 LINE IN Press to select the component connected to the Audio/Video jacks. 14 PRE-CH (previous channel) Press to return to the last channel viewed. 15 MUTE Press to silence the volume. 16 P.STD (picture-standard) Press to select memorized or standard picture settings. 10 CHAPTER ONE: LEARNING ABOUT YOUR NEW TV/VCR LEARNING ABOUT YOUR NEW TV/VCR Understanding the Controls, continued Remote Control Use the remote control within 33 feet (10 meters) of the TV/VCR and point it directly at the TV/VCR. 17 EJECT Press to eject a tape. 18 REC (record) Press to begin recording. 19 TRK+, – (tracking) Press to adjust tape tracking. 20 P.PLUS Press to compensate for a poor rental tape. 21 P. (pause) /STILL Press to freeze a video frame. 22 SPEED Press to select the tape recording speed. 23 F.ADV (frame advance)/ SKIP Press to advance a tape frame-by-frame or to use skip search. 24 SLOW+, – Press to watch a tape in slow motion. 25 REPEAT Press to play a tape or a section of tape repeatedly. CHAPTER ONE: LEARNING ABOUT YOUR NEW TV/VCR CHAPTER TWO INSTALLATION Connecting VHF UHF Antennas If you do not have cable TV, you must connect an antenna to your TV/VCR. First you need to identify your antenna’s lead type: • If you are using the antenna that has 300-ohm twin flat leads, (see the illustration below) see “Antennas With 300-ohm Flat Twin Leads,”on this page. • If your antenna has a 75-ohm round lead (see the illustration below), see “Antennas With 75-ohm Round Leads,” on this page. • If you have two antennas, see “Separate VHF and UHF Antennas,” on this page. Antennas With 300-ohm Flat Twin Leads If you use a different 300-ohm antenna with twin flat leads, follow the directions below, but skip step 1. 1 Push the stem of the rod antenna into the antenna mount. 12 CHAPTER TWO: INSTALLATION 2 Place the wires from the twin leads under the screws on the 300-75 ohm adapter. Use a screwdriver to tighten the screws. 3 Plug the adapter into the terminal on the rear panel of the TV/VCR. Extend the antenna and adjust it for the clearest picture.To reduce the risk of damage, only adjust the antenna by moving the black plastic base. Antennas With 75-ohm Round Leads 1 Plug the lead into the terminal on the rear panel of the TV/VCR. Separate VHF and UHF Antennas If you have two separate antennas for your TV/VCR (one VHF and one UHF), you must combine the two antenna signals before connecting them to the TV/VCR. This procedure requires a combiner attachment that you can purchase at an electronics store. INSTALLATION Connecting VHF Antennas, continued If you use a different 300-ohm antenna with twin flat leads, follow the directions below, but skip step 1. 1 Push the stem of the rod antenna into the antenna mount. 2 Connect both antenna leads to the combiner. 3 Plug the combiner into the terminal on the rear panel of the TV/VCR. Connecting Cable Systems to the TV/VCR Choose one of the sections below for connecting a cable system. . This TV/VCR is cable-ready; you don’t need a converter for basic cable channels. Cable Without a Converter Box To connect cable without a converter box: 1 Plug the incoming cable into the terminal on the rear panel of the TV/VCR. Cable With a Converter Box If your cable company scrambles some channels and requires you to use a converter box for only those channels, use these instructions. You will need the following pieces of equipment, which you can purchase from an electronics store: • A two-way splitter • An RF (A/B) switch • Four lengths of coaxial cable 1 Plug the incoming cable into the 2-way splitter. CHAPTER TWO: INSTALLATION INSTALLATION Connecting Cable to the TV/VCR, continued 2 Connect one of the coax...
Otros modelos de este manual:TV - CXM 1374 (1.59 mb)
TV - CXM1974 (1.59 mb)
TV - CXM1974 (1.59 mb)