Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Improper installation may result in damage to the screen, property, or personal injury. What You Will Need You will need these tools to install your wall mount bracket: • Measuring tape • Level • Pencil or pen • Electric drill • Hammer • Ratchet with 7/16 inch socket • Phillips screwdriver • Stud finder (for wood stud wall) • 3/16 inch Drill bit (for wood stud wall) • Masonry drill bit (for concrete wall) • Concrete screw anchors (for concrete wall) Before You Begin 1 What You Will Need 1 Package Contents 2 Installation 3 Wood Stud Wall Installation 3 Concrete or Concrete Block Wall Installation 4 Specifications 6 K2Mounts Warranty 7 Package Contents Verify that you have received all of the parts listed below: Articulating Arm/Wall Mounting Plate Screen Plate Wall Hardware Screen Hardware 6 - 3” X 7/16” lag bolts 6 - 3/4” washers Hex wrench 6 - 3/8” x 1/2” black spacer 6 - 3/8” x 3/4” black spacer 6 - 3/4” washers 6 - 7/16” washers 6 - M6 x 30mm screws 6 - M6 x 15mm screws 6 - M5 x 30mm screws 6 - M5 x 15mm screws 6 - M4 x 30mm screws 6 - M4 x 12mm screws If any parts are missing or damaged, contact K2Mounts at support@k2mounts.com for a replacement. K2Mounts is not liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect usage. Installation To mount to a wood stud wall, continue below. To mount to a concrete wall, go to page 4. Wood Stud Wall Installation Locate the Wall Studs Wall studs run vertically (up and down) inside the wall, behind the drywall or plaster. You must attach the mounting plate to two separate wall studs that run from floor to ceiling. This mount requires that the wall studs be 16 inches apart (on center). 1. Using the stud finder, mark the left and right edges of the studs closest to where you want to mount the screen. 2. Mark the centerline of each stud. Drill Mounting Holes 1. If you have the installation poster: a. Tape the poster to the wall with the ACTUAL SIZE TEMPLATE side showing. Line up the mounting holes with the centers of the wall studs. Level the Articulating Arm/ Wall Mounting Plate. b. Drill where indicated with a 3/16” drill bit, 2 1/2” deep. If you do not have the installation poster: a. Hold the Articulating Arm/Wall Mounting Plate up to the wall, lining up the left-most and right-most mounting holes and with the centers of the wall studs. Level the Articulating Arm/Wall Mounting Plate. b. Make marks on the wall through all the left-most and right-most holes and then remove the Articulating Arm/Wall Mounting Plate from the wall. c. Drill five holes at the marks with a 3/16” drill bit, 2 1/2” deep. Anchor Articulating Arm/Wall Mounting Plate to the Wall 1. Using the ratchet and 7/16 inch socket, anchor the Articulating Arm/Wall Mounting Plate to the wall with five of the 7/16” x 2” Lag Bolts and Washers from the Wall Hardware bag. 2. Go to “Attach the Screen Plate to the Screen” section on page 5. 2" x 4" 2" x 4" If you have 16" on-center studs or are mounting to concrete, drill were indicated. Turn over for installation instructions. ACTUAL SIZE TEMPLATE Concrete or Concrete Block Wall Installation ! Warning: Attaching the wall mount to a brick wall could result in property damage or personal injury. Obtain Concrete Anchors The hardware needed to mount to a concrete wall is not included. Purchase at least 5 concrete anchors with a weight rating that will accomodate your screen plus the weight of the mounting bracket (about 16 lbs.). Install Anchors 1. If you have the installation poster: a. Tape the poster to the wall with the ACTUAL SIZE TEMPLATE side showing. b. Install the anchors where indicated on the poster. If you do not have the installation poster: a. Hold the Articulating Arm/Wall Mounting Plate up to the wall where you want to mount the bracket. b. Make marks on the wall through all the left-most and right-most holes. Remove the Articulating Arm/Wall Mounting Plate from the wall. c. Install anchors at the marks you made in the previous step. Anchor Wall Mounting Plate to Wall 1. Anchor the Articulating Arm/Wall Mounting Plate to the wall with at least five Lag Bolts and Washers. If you use the bolts and washers from the Wall Hardware bag, make sure that they are suitable for the anchors used. 2. Go to “Attach the Screen Plate to the Screen” section on the next page. If you have 16" on-center studs or are mounting to concrete, drill were indicated. Turn over for installation instructions. ACTUAL SIZE TEMPLATE Attach the Screen Plate to the Screen 1. Line up the holes in the Screen Plate with the holes on the back of the screen. 2. If the screws that came with your screen hold the plate securely, use them, otherwise use screws from those provided in the Screen Hardware bag. 3. Attach the Screen Plate with a washer and then a screw in each hole. Attach the Screen Plate to the Arm 1. Using the hex wrench provided in the Screen Hardware bag, remove the upper hex screws protruding from the arm. Then hook the bottom of the Screen...