Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
16:9 TV is easily falled by pulling or pushing it. Specially when children hang on TV or climb on it, there accident could occur. Install prevention of conduction for safety. 1. Hold fixing hole and clamp by screw in the back of TV 2. Bind it to steadily strong wall or prop by hard strings It is safe that strings is bound like right picture. When you move the TV, you should attention the strings. Use prop for TV that can stand the weight of TV Information of setting up TV Table of Contents Table of Contents Installation and Maintenance Antenna Connection 8 Video Connection 11 Camcorder & Play station Connection 12 DVD Connection 13 Audio Connection 14 Digital Satellite Receiver Connection 15 Cable TV Broadcasting Connection 16 Name of Each Part 18 Basic Guide To setup device change of remote control 22 Method To Use Basic Menu 23 To Watch TV 24 Automatic Channel Memory 26 Selection of Input Signal 32 Application Guide Screen Adjustment 35 Selection of PIP 44 Sound Adjust 49 Adjustment of Color Match 56 Selection of Language 58 Troubleshooting 59 Standard of Product 60 -7 Antenna Connection Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. 2. Connect the combining adapter to the antenna input at the back of the TV set. WHEN USING THE COMBINING ADAPTER You may obtain the combining adapter at your closest Service Center. Antenna Input -8 CTV Antenna Connection Such community TV Antenna installation may be found in most of co-op apartments. When a coaxial cable is used Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right. ANT/CABLE 1 When a feeder cable is used ANT/CABLE 1 -9 Outdoor Antenna Connection Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses Single Antenna Connection. VHF Antenna UHF Antenna ANT/CABLE 1 Separate Antenna Connection. ANT/CABLE 1 -10 Video Connection Connecting with an External Source Video Connection Connecting with an External Source You may connect S-Video input to enjoy a clearer and brighter picture images. You can choose and make the connection with any one of Video 1,2, or 3 inputs. Connection is not necessary in Mono mode. Connect either S-Video or Video input to the unit. When both are connected, the output display will be in S-Video. The following connection allows you to record TV programs. Connecting with an Antenna ANT/CABLE 1 Note The stated connection does not comply with recording TV programs. You must make the connection to the Antenna input socket as shown below for recording. Connection Guide 1. Connect the antenna to the antenna input of the video 2. Make a connection of Antenna Output on Video and Antenna Input on TV with the coaxial cable provided. Operating Instructions 1. Adjust the channel selection switch at the rear side of the Video to 3 or 4. 2. Turn on the TV set, and adjust the channel to 3 or 4, to the number adjusted for step1. 3. Turn on the Video, insert the videocassette, and press the Play button. -11 Camcorder & Play station Connection Watching the Camcorder Recording on TV Camcorder & Play station Connection Watching the Camcorder Recording on TV -Use the input jack provided at the side panel of the TV set -Use the same connection method for playstation Video game Playing a Recorded Material and Recording a Video simultaneously -Connect the camcorder and video as follows. -Turn the camcorder's video output switch on, and play the recorded material. -Press the "TV/VIDEO" button, and select Video 1. -Select A/V INPUT for the Video Input, and start recording. -12 DVD Connection DVD DVD Connection DVD -480i input signal is possible for DVD input. -DVD screen output is composed of three separate primary color jack(Y/Cb/Cr), resulting in a higher image quality. -Y/Cb/Cr, may also be noted as Y/PB/PR or Y/Pb/Pr in different DVD players. -The DVD player s audio output must be connected to the DVD audio input socket at the back of the TV set. -You must use a 480p input capable DTV jack if you want to get the progressive scan (480p) DVD screen display. -13 Audio Connection Audio Connection Standard Audio Connection -You may minimize the volume of the TV set, and listen to the sound. -The default status of Dolby Virtual is in Line out: Internal . -14 Digital Satellite Receiver Connection Watching High Definition Digital Broadcasting Digital Satellite Receiver Connection Watching High Definition Digital Broadcasting The signal input of 1080i, 720p, and 480p are available in this product. You may use a general A/V jack for its connection. Digital Satellite Receiver -15 Cable TV Broadcasting Connection External Input Connection Source Cable TV Broadcasting Connection External Input Connection Source Watching cable telev...
Otros modelos de este manual:TV - 5520CRA (12.39 mb)
TV - DSJ-4710CRA (12.39 mb)
TV - DSJ-4720CRA (12.39 mb)