Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Input Selection Buttons: Use these buttons to select an input source directly or to enter numeric characters, as follows. 12.VIDEO (1) Press to select Composite video input as the source. 13.S-VID 1 (2)/ S-VID 2 (5) (S-Video) Press to select an S-Video input. 14.COMP (Component) (3) Press to select Component SD (480i/576i) video input as the source. 15.HD 1 (4) / HD 2 (7) Press to select a HD (RGBHV or YPbPr component) input. 16.DVI 1 (6) / DVI 2 (8) Press to select a Digital Video input. Aspect Ratio Selection Buttons: Use these buttons to select an aspect ratio directly or to enter numeric characters, as follows. 17.ANA (Anamorphic) (9) For viewing 16:9 DVDs or HDTV programs in their native aspect ratio. 18.4X3 (Standard 4:3) (0) Scales the input signal to fit 4:3 display mode in the center of the screen. 19.LETBOX (Letterbox) For viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen. 20.I-WIDE (IntelliWide) Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display. 21.CINEMA For viewing 2.35:1 source material. 22.SVC Selects the IntelliWide 2.35 aspect ratio, used for viewing 16:9 source material on a 2.35:1 screen. 3Installation 3.1 Remote Control To install batteries in the remote control, press up on the battery cover retainer clip and lift off the cover. Install the two AAA batteries with the correct polarity and then replace the cover. Notes on Batteries •Make sure that the battery polarities are correct when installing the batteries. •Do not mix an old battery with a new one or different types of batteries. •If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage. Notes on Remote Control Operation •Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector. •If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones. •The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. •Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the projector, and repeat the operation. 3.2 Quick Setup Table 3-1 gives a quick overview of the Vision 90t/100t installation process. The sections following this one provide detailed instructions. Note Installation should be performed by a qualified custom video installation specialist. Table 3-1. Installation Overview Step Procedure For Details, Refer to page... 1 Choose a location for the projector 15 2 Install CineWide (secondary anamorphic) lens (optional) 20 3 Connect signal sources to the projector 21 4 Connect external controller to RS-232 port (optional) 25 5 Connect other home theater components to 12-volt trigger outputs (optional) 25 6 Apply power to the projector 26, 27 7 For rear-screen and/or ceiling-mount installations, select the proper picture orientation 27 8 Lens adjustments: projected image size (zoom), position (shift) and focus 18, 28 9 Projector calibration: adjust the following for each input, starting with Component SD; save settings when finished: • Aspect ratio • Brightness • Contrast • Color level • Tint • Input position 30 through 37 3.3 Installation Considerations Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally. Installation Type Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount. Table 3-2 compares these various installation methods. Table 3-2. Projector Installation Options Advantages Considerations Front Screen, Floor Mount Installation • Easy to set up • Can be moved or changed quickly • Easy to access • Shares floor space with audience Front Screen, Inverted Mount (ceiling) Installation • Does not take up audience space • Projector is unobtrusive • Projector cannot be accidentally moved • Installation is more permanent • Projector access is more difficult Rear Screen, Floor Mount Installation • Projector is completely hidden • Projector is easily accessed • Usually good ambient light rejection • Requires separate room • Installation cost is usually higher Rear Screen, Inverted Mount (ceiling) Installation • Projector is completely hidden • Usually good ambient light rejection • Requires separate room • Installation cost is usually higher Rear Screen, Floor Mount with Mirror • Projector is completely hidden • Usually good ambient light rejection • Requires less space behind screen than other rear screen installations • Requires separate room • Installation cost is usually higher Ambient Light In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your images will be noticeably reduced if light directly strikes the scree...
Otros modelos de este manual:TV - Vision 100t (4.17 mb)