Votos - 0, Puntuación media: 5
(
)
)
|
Resumen del manual
O Connect one end of a coaxial cable to the ANTENNA OUT terminal on the VCR. Connect the other end of the coaxial cable to the ANT-A terminal on the TV. O Connect an RCA pin-type video cable to the VIDEO OUT terminal on the back of the VCR. Connect the other end of this cable to the VIDEO INPUT r_erminal on the back of the television. If you are connecting a Super VHS (S-VHS) VCR, use an S-Video cable instead of an RCA pin-type video cable. Connect this S-Video cable to the S-VIDEO OUT terminal on the VCR. Connect the other end of this cable to the S-VIDEO INPUT terminal on the back of the TV. O Connect a set of RCA pin-type audio cables, to the AUDIO OUT terminals on the back of the VCR. Use the red cable to connect the right (R) channel and the white cable for connecting the left (L) channel. Connect the other ends of this cable to tile AUDIO INPUT terminals on the back of the TV. If your VCR is monaural (non-stereo), you only need to connect a single RCA pin-type audio cable. Connect the cable to the VCR, then connect the other end to the L (LEFT) au,iio input on the back of the TV. If your VCR has a video channe! switch, set it to "OFF/AV". See your VCR's owner's guide for details. Start playing a tape on your VCR. O Use the INPUT button on your TV's remote control to select the correct input. If you connected the VCR tc, INPUT-l, select Input-l; if you connected the VCR to INPUT-2, select Input-2. 30 Chapter 2: Connecting Your TV TV + VCR + antenna or cable without a cable box (cont.) 0 VCR Rear ._@ IN Antenna @ OUT VCR Rear Terminals VIDEO OUT O 0 TV Rear T f inals Incoming Cable or Antenna O ANT A CABLE LOOP-OUT ANT 4B ACTIVE AN ® Basic Connections TV + VCR + cable with a cable box equipment you will need This hook-up will allow you to record scrambled channels while viewing another channel. To complete the hook-up, you will need: Three lengths of 75 ohm coaxial cable • One set of RCA pin-type audio cables One RCA pin-type video cable (if connecting a standard VCR) OR • One S-Video cable for Super VHS VCRs 32 Chapter 2: Connecting Your TV TV + VCR + cable with a cable box (cont.) procedure (See illustration on the following page.) O Connect the incoming cable to the ANT-A terminal on the back of the TV. O Connect a coaxial cable from the cable LOOP-OUT terminal[ on the back of the TV to the cable box IN terminal. Connect a second coaxial cable from the OUT terminal on the cable box. Connect the other end of this cable to the ANTENNA-IN terminal on the back of tile VCR. O Connect the third coaxial cable from the OUT terminal on tlhe back of the VCR to the ANT-B terminal on the back of the _V. O Connect an RCA pin-type video cable to the VIDEO OUT terminal on the back of the VCR. Connect the other end. of this cable to the VIDEO INPUT terminal on the back of the TV. _>Important: If you are connecting a Super VttS (S-VHS) VCR, use an S-Video cable instead of an RCA pin-type video cable. Connect this S-Video cable to the S-VIDEO OUT terminal on the VCR. Connect the other end of this cable to the S-VIDEO INPUT terminal on the back of the TV. Connect a set of RCA pin-type audio cables to the AUDIO OUT terminals on the back of the VCR. Use the red cable to connect the right (R) channel and the white cable for connecting the left (L) channel. i Connect the other ends of this cable to the AUDIO II_PUT terminals on the back of the TV. _>Important: If your VCR is monaural (non-stereo): you will only need to c,onnect a single RCA pin-type audio cable. Connect the cable to the audio out terminal of the VCR, then connect the other end to the L (LEFT) audio input on the back of the TV. E>Important: If your VCR has a video channel switch, set it to "OFF/AV'. See your VCR's owner's guide for details. Basic Connections TV + VCR + cable with a cable box (cont.) 0 Start playing a tape on your VCR. 0 Use the INPUT button on your TV's remote control to select the correct input. If you connected the VCR to INPUT-l, select Input-1. If you connected tile VCR to INPUT-2, select Input-2. VCR Rear VCRRearTerminals ___ F-White Lead L_-"_J _ _,_------_ / / _..--._ Yellow Lead 0 WhitE! Lead--, " r_-. I TV RearTerminals S-Video Cable 0 0 CABLE ANT-A LOOP_3UT ANT-B @@ AC_VE A_ NETWO_ ® i 34 Chapter 2: Connecting Your TV TV + stereo audio system You may want to hear the sound from your TV and/or VCR through your home audio system. To do this, complete the necessary connections shown on previous pages of this .chapter, then follow the procedure on this page. equipment you will need __--_ need % •o oo pa.a io y e ,yo H • One set of RCA pin-type audio cables. procedure 0 Connect the audio cables to the AUDIO MONITOR OUTPUT terminals on the back of the TV. Use the red cable to connect the right (R) channel and the white cable to connect the lefL (L) channel. O Connect the other ends of these cables to the AUX IN terminals on the back of the audio system. Turn off the television's speakers. To do tlhis, press the AUDIO thnction button on ...
Otros modelos de este manual:TV - VS-45501 (3.36 mb)
TV - VS-50501 (3.36 mb)
TV - VS-50502 (3.36 mb)