Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the battery. 1. Press the [PWR] button. 2. The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode. 3. Press the [PWR] button to turn off the power for the unit. Standing up the liquid crystal panel 1. Press the [OPEN/CLOSE] button and the liquid crystal panel comes out and stand up automatically. . While the liquid crystal panel is opening or closing, the LED of the [RESET] button blinks. Note: • If the liquid crystal panel stops in the middle of its operation, press the [OPEN/CLOSE]button to house the panel and press the button again to stand it up. The unit enters the same display mode as the display was turned off the last time. Adjusting the angel, etc. of the liquid crystal panel The angle of the liquid crystal panel or protruding amount of the panel from the mounting surface can be adjusted depending on the mounting angle of the unit or light coming into the car. To adjust the angle 1. Every time the [TILT] button is pressed, the liquid crystal panel tilts forward or backward at up to about 20 degrees. The adjusted angel is stored in memory. 20° 20° 10 TB741P/TB742P/TB743W Basic Operations Note: • Do not move the liquid crystal panel by hand. To adjust the slide position 1. Press and hold the [TILT ] button and release when a beep is heard. The liquid crystal panel slides forward or backward. The adjusted slide position is stored in memory. . There are 3 adjustable positions available on this panel. Housing the liquid crystal panel 1. Press the [OPEN/CLOSE ] button and the liquid crystal panel is housed automatically. Note: • When leaving this unit unused for a long period of time or leaving your car, be sure to house the liquid crystal panel into the main unit. Turning the liquid crystal panel horizontal (Air conditioner operation mode) When the way the liquid crystal panel is mounted hinders the operation of the air conditioner, the position of the panel can be turned horizontal temporarily. 1. Press and hold the [OPEN/CLOSE ] button when the liquid crystal panel is upright, and release the button when a beep is heard. 2. The liquid crystal panel turns horizontal. . Press the [OPEN/CLOSE ] button again when the liquid crystal panel is in the horizontal position, and the panel returns to the original position. . Even if the button is not operated for about 10 seconds, the panel returns to the original position with a warning sound. Turning on and off the monitor 1. Pressing and holding the [BND ] button for 1 second or longer turns the monitor off. To return to the monitor on, press the [BND ] button once again. . When a button is pressed or during security monitoring, the monitor-off mode is canceled. Car stereo adjustments 1. Set the car stereo’s radio frequency to the modulator frequency. (TB741P/TB742P only) . The factory set for the modulator frequency is 88.1 MHz. (Refer to the section on selecting the FM modulator frequency on page 15.) 2. Use the car stereo’s volume and tone controls to adjust the volume and tone to the desired levels. Note: • Adjust also the BASS (bass)/TREB (treble) and BAL (left/right balance)/FAD (front/back balance) controls to the optimum positions. English Owner’s manual TB741P/TB742P/TB743W 11 Basic Operations English Owner’s manual Note: Selecting the screen size • When the wide mode or full wide mode is used to Four screen display modes are supported: display a normal 4:3 picture which is not a wide normal, wide, full wide and cinema. picture so that it fills the whole wide TV screen, parts of the picture around the edges will be off Note: the screen or the picture will be distorted on the • The screen mode cannot be selected while the screen. To view original pictures so as to respect vehicle is in motion. the intentions of the producer, use the normal mode. Press the [DISP] button for 1 second or longer to select the screen display mode. Each time this button is pressed for 1 second or longer, the display mode is changed in the sequence shown below. For normal 4:3 picture reception Depending on which mode is set, the shape of the picture will be distorted on the screen. Full wide mode Cinema mode 62TV1F.WIDE62TV1CINEMA The whole picture is stretched The picture at the top and bottom in the sideways direction. of the screen is off the screen. Wide mode Normal mode (normal screen) 62TV1WIDE62TV1NORMAL The picture at the left and right of the screen is stretched in the sideways direction. In wide mode, the picture is stretched in both the upward and downward direction when a PAL signal is received. For wide (16:9) picture reception Use the cinema mode. Normal mode 62TV1NORMAL Black bands appear all around the screen. Black bands appear to the left and right of the screen. Cinema mode 62 TV1 CINEMA Wide mode, full wide The picture is show...
Otros modelos de este manual:TV - TB742P (957.76 kb)
TV - TB743W (957.76 kb)