Votos - 4, Puntuación media: 4.5 ( )

Fabricar: Panasonic Tamaño del archivo: 1.18 mb Nombre del archivo: Idioma del manual:

For Example: TV Power/On, VCR Power/On, and Cable box Power/On (selected brands) can be operated at the same time with one press of the MULTI button. (The VCR Mode button should be programmed before starting procedure). Procedure 1. Program the Remote for the selected device Infrared access code. Confirm that the Remote Control is compatible with the device. 2. Face the Remote Control transmitter away from all equipment remote sensors. 3. Press and hold the Remote POWER button, then press and hold the ACTION button down at the same time for three seconds. (All previous commands are erased.) PRESS AT THE SAME TIME FOR THREE SECONDS 4. 5. 6. After three seconds, release the POWER and ACTION buttons. Press the MULTI button. (Waiting more than 30 seconds without pressing another button will exit the programming mode.) Press a maximum of six (6) function buttons on the Remote Control. Each button you press is equal to one function. If six (6) Remote button functions are entered, all will register in the MULTI button memory in the sequence entered. When finished, press the MULTI button to exit the programming mode. The following is an example flow chart of. Remote functions that can be programmed into the MULT! button. You can now turn the TV and VCR ON/OFF at the same time with one press of the MULTI button. To delete entered functions - Press and hold the Remote POWER button, then press and hold the ACTION button down at the same time for three seconds. You can now enter from one to six different Remote functions. Note: You can also program the MULTI button to perform most individual Remote Control button functions. Buttons which continuously perform a function as long as pressed (Volume Up/Down, Channel Up/Down, etc.) cannot be programmed; only those buttons which perform a function when initially pressed (Power On/Off, Mute, Direct Channel Entry, etc.) can be programmed. -13- Special Functions (cont.) PIP (Picture in Picture) Button This feature allows the viewer to monitor one channel program while watching another. The monitored source (PIP) can be a different channel or a different video source (such as a VCR) when connected to the input jacks. • When the Main Picture is in Video mode with no signal, the PIP will not operate properly. PIP Operation 1. Turn VCR ON and select a desired channel. 2. Press the TV Mode Selection button to operate TV Remote functions, if necessary. Swap Button Press the SWAP button (when the PIP frame is displayed) to interchange what is being viewed on the Main Picture with that of the PIP frame. VIDEO 1 PIP CH 2 Note: Audio will be that of Main Picture. 3. Press the PIP button (set must be ON). The PIP frame will appear at the position it was last displayed. The Main Picture Video Source and PIP Video Source will display on screen momentarily. Audio will be that of Main Picture. Size Button Press the SIZE button (when the PIP frame is displayed) to choose either the large or small PIP frame. Main Picture with — Audio Main Picture Channel Picture in Picture Video Source Picture in Picture Frame 4. Press the PIP button again to cancel PICTURE IN PICTURE feature (if desired). pip Note: For PIP Video source connection, refer to the PIP External Video and Antenna Connections section. -14- Special Functions (cont.) Freeze Button Press the FREEZE button to stop action in the PIP frame. ______ FREEZE Notes: • Pressing the FREEZE button when the PIP frame is not displayed, will stop action in the Main Picture and display it within the PIP frame. • Pressing the FREEZE button when PIP frame is displayed, will stop action in the PIP frame. Press the FREEZE button again to continue action. • Press the PIP button to delete PIP frame. Move Button The PIP frame may be located at any corner of the Main Picture by pressing the PIP MOVE button (when the PIP frame is displayed). MOVE Note: Each time MOVE button is pressed (when the PIP frame is displayed), the PIP frame will move counterclockwise as illustrated. PIP Channel Buttons - Press the PIP CHANNEL UP or DOWN button while the PIP frame is displayed to sequentially scan through Channels. PIP CHANNEL Scan Channel DOWN (next lower) Scan Channel Up (next higher) Search Button - The search button allows you to scan channels in “Channel Scan memory” one at a time. This feature will work with or without an external video signal as the Main Picture. SEARCH Search Operation 1. Press the SEARCH button. A PIP frame will appear on the Main Picture. (The PIP frame will continuously scan channels in sequence as programmed into channel memory.) 2. Two Options: Option 1. Press the SEARCH button again, the Search frame will disappear. Option 2. Press the PIP button to stop Search feature on desired picture for PIP frame. (Press the SWAP button to interchange what is being viewed on the Main Picture with that of the PIP frame. Main Menu Icons NOTE: When Auto Power On feature is ...

Descargar ahora

Introduzca dos números de la imagen: