Votos - 2, Puntuación media: 3.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Instruction Remote Control Batteries for the Remote book Transmitter Control Transmitter EUR646525 (AA(R6) Battery . 2) PLASMA DISPLAY INPUT SURROUND VOL N R PICTURE SOUND SET UP ASPECT PICTURE POS. /SIZE OFF TIMERPC Fixing bands TMME187 . 2 Ferrite core J0KF00000018 . 2 AC cordWarranty Optional Accessories • Speakers • Pedestal • Wall standTY-SP42PWD3W TY-ST42PT3-K TY-ST42PW1 • Wall-hanging bracket • Tuner terminal board • Connecting Cable(angled)TY-42TM4H TY-SCP15C03 TY-WK42PR1 49.2 ft (15 m) For assembling Full instructions are supplied with each optional accessories for use with this Plasma Display. Remote Control Batteries Requires two AA batteries. 1. Turn the transmitter face down. 2. Install the batteries as shown in 3. Replace the cove and slide in Press and slide off the battery the battery compartment. reverse until the lock snaps. cover. (Polarity + or – must match the markings in the compartment). Two "AA" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. Basic Controls R - STANDBY G POWER ON INPUT – VOL + TY-42PW4 Main Power On/Off Switch Volume Adjustment Push the Volume Up “+” orInput button (VIDEO (S VIDEO)/COMPONENT, Power Indicator The Power Indicator will light. • Power-OFF ..... Indicator not illuminated (The unit will still consume some power as long as the RGB/PC Mode Selection) Push the “INPUT” button to select VIDEO(S VIDEO)/COMPONENT or Down “–” button to increase or decrease the sound volume level. power cord is still inserted into the wall outlet.) RGB/PC input signal modes sequentially. • Stand-by .... Red • Power-ON ...... Green Input button (VIDEO(S VIDEO)/COMPONENT, RGB/PC Mode Selection) Press to select VIDEO(S VIDEO)/ COMPONENT or RGB/PC input signal modes sequentially. (see page 19) Sound mute On/Off (see page 26) Volume Adjustment Press the Volume Up “+” or Down “–” button to increase or decrease the sound volume level. R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 20) SOUND button (see page 26) ASPECT button Press to adjust the aspect. (see page 22) OFF TIMER button This button is used to switch The Plasma Display may be preset to switch to stand-by after a fixed period. The directly to PC mode. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. When three minutes remain, “Off timer 3” will flash. The off timer is cancelled if a power interruption occurs. PC button Push the “PC” mode selection button to select the PC mode. INPUT SURROUND VOL N R PICTURE SOUND SET UP ASPECT PICTURE POS. /SIZE OFF TIMERPC Stand-by (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 18). Push this button to turn the Plasma Display ON, from STANDBY mode. Push it again to turn the High Definition Plasma Display OFF to STANDBY mode. SURROUND button (see page 27) N button (see page 25, 26, 28, 29) PICTURE button (see page 28) PICTURE POS./SIZE button (see page 24) Status button Push the “Status” button to display the current system status. 1 VIDEO(S VIDEO)/COMPONENT, RGB/PC mode 2 Aspect mode (see page 22) 3 Off timer The off timer indicator is displayed only when the off timer has been set. OFF TIMER 90 1 2 3 VIDEO NORMAL 30 60 0 90 Connections SPEAKER SPEAKER Terminals (L) Terminals (R) To tighten: To loosen: Push the catch Pull Pull 1 2 – Cable fixing bands Secure any excess cables with bands, as required. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. PR/CR/R PB/CB/B Y/G COMPONENT/RGB INAV IN VD HDS VIDEOVIDEO R L AUDIO R L AUDIO AUDIO PC IN SERIAL From SERIAL Terminal on Computer (see page 17) From EXIT monitor Terminal on Computer (see page 16) COMPONENT/RGB IN and Audio IN Terminals (see page 14,15) AV IN Terminals (see page 13, 14) Connections Speakers connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. 1 1 2 2 Speakers (Optional accessories) ...