Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
^ The interlace mode is not supported. ^ The set might operate abnormally if a non-standard video format is selected. ^ Separate and Composite modes are supported. SOG is not supported. English - 44 Setting up the TV with your PC Auto Adjustment in progress Please wait. Tools Anynet+ (HDMI-CEC) Picture Mode : Standard Sound Mode : Custom Sleep Timer : Off SRS TS XT : Off Energy Saving : Off I Auto Adjustment TV ift s Fine Position Image Reset 3 > !*) *r- _ ▼ Move S1 Enter Í) Return >• Preset: Press the SOURCE button to select PC mode. 1. Press the MENU button to display the menu. Press the ENTERS' button, to select "Picture". 2. Select the required option by pressing the ▲ or ▼ button, then press the ENTERS button. 3. When you are satisfied with your setting, press the ENTERS button. 4. Press the EXIT button to exit. ♦ Auto Adjustment Auto adjustment allows the PC screen of set to self-adjust to the incoming PC video signal. The values of fine, coarse and position are adjusted automatically. Easy Setting 1. Press the TOOLS button on the remote control. 2. Press the ▲ or ▼ button to select “Auto Adjustment”, then press the ENTERS button. ♦ Screen Adjustment: Coarse/Fine The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen. Press the ▲ or ▼ button to select "Coarse" or "Fine", then press the ENTERS button. Press the ◄ or ► button to adjust the screen quality. Press the ENTERS button. Position Adjust the PC's screen positioning if it does not fit the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position Press the ◄ or ► button to adjust the Horizontal-Position. Press the ENTERS button. Image Reset You can replace all image settings with the factory default values. English - 45 What is Anynet+? Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling all connected AV devices through the Anynet+ menu When Samsung Electronics AV devices are connected. Connecting Anynet+ Devices_ The Anynet+ system supports AV devices supporting Anynet+ only. Check if there is an Anynet+ mark on the AV device to be connected to the TV. To directly connect to TV Connect the [HDMI 1], [HDMI 2] or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. To connect to Home Theater 1. Connect the [HDMI 1], [HDMI 2] or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. 2. Connect the HDMI IN jack of the home theatre and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. ^ Connect only the optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio Input on the receiver. ^ Connect only one receiver. ^ You can listen to 5.1 channel sound through the home theatre's speakers. Otherwise, you can only listen to 2 channel stereo sound in other cases. Make sure to connect the Digital Audio IN (Optical) of the home theatre and the TV correctly to listen to TV sound through the home theatre. However, you cannot listen to sound from the BD recorder that is sent to the home theatre via the TV in 5.1 channel sound because the TV outputs only 2 channel stereo sound. Please see the manual for the home theatre. ^ You can connect an Anynet+ device using the HDMI cable. Some HDMI cables may not support Anynet+ functions. ^ Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status. ^ Anynet+ supports up to 8 AV devices in total. English - 46 Setting Up Anynet+ I Anynet+ (HDMI-CEC) Picture Mode Standard Sound Mode Custom Sleep Timer Off SRS TS XT Off Energy Saving Off Dual l-ll Mono TV P9 ^ View TV Select Device 0 Record 0 1 Menu on Device 0 — Device Operation 0 '■, Receiver :Off 0 Setup 0 ^ Move B1 Enter ■D Return Setup Anynet+ (HDMI-CEC) Off Auto Turn Off : m Searching Connections ▼ Move 0 Enter *D Return The following settings are to use Anynet+ functions. Using the Anynet+ Function 1. Press The TOOLS button. Then Press the ENTERS' button to select "Anynet+(HDMI-CEC)". Press the ▲ or ▼ button to select "Setup", then press the ENTERS button. 2. Press the ENTERS button to select "Anynet+ (HDMI-CEC)", then press the ENTERS button. 3. Press the ▲ or ▼ button to select "On", then press the ENTERS button. ^ The "Anynet+ (HDMI-CEC)" function is enabled. ^ If you select "Off', "Anynet+ (HDMI-CEC)" is disabled. ^ When the "Anynet+ (HDMI-CEC)" function is disabled, all the Anynet+ related operations are deactivated. Turning an Anynet+ Device Off Automatically when the TV is Turned Off 1. Press the ▲ or ▼ button to select "Auto Turn Off", then press the ENTERS button. 2. Press the ▲ or ▼...
Otros modelos de este manual:TV - LE26A456C2D (9.34 mb)
TV - LE32A455C1D (9.34 mb)
TV - LE32A456C2D (9.34 mb)
TV - LE32A457C1D (9.34 mb)