Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Size: / / You can select a size of the sub-picture. . If main picture is in PC and Component mode, Size is not available. . Position: / / / Return . . .. T V Return Standby Mode On . . . T V Return . . .. T V Return Standby Mode On . . . T V You can select a position of the sub-picture. . You can select these options simply by pressing the POSITION button on the remote control. . ProgrammeYou can select a channel of the sub-picture only when the Source is set to TV. . You can select the channel of the sub picture simply by pressing the P or P button. English - 28 Screen Burn Protection To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allowsyou to program the time between movement of the picture inminutes. 1 Press the MENU button to display the menu. 2 Press the ^ or Ў button to select Setup, then press theENTER button. 3 Press the ^ or Ў button to select Screen Burn Protection, then press the ENTER button. 4 Select the required option by pressing the ^ or Ў button, thenpress the ENTER button. Available options: Pixel Shift, All White, Signal Pattern, Side Gray 5 When you are satisfied with your setting, press the ENTER button. 6 Press the EXIT button to exit. . Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after image on the screen. . Set Pixel Shift to On by pressing the ^ or Ў button, then press the ENTER button. . Select the required option by pressing the ^ or Ў button, then press the ENTER button. Available options: Horizontal Dot, Vertical Line, Time . Optimum condition for pixel shift; PC Horizontal Dot 1 Vertical Line 1 Time (minute) 2 min TV/Ext/Component/HDMI 2 2 2 min . The Pixel Shift value may differ depending on the monitor size (inches) and mode. . All White: This function helps remove after images on the screen by changing the colour of pixels to white. Use this function when there are remaining after images or symbols on the screen especiallywhen you displayed a still image on the screen for a long time. . Signal Pattern: This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time. . Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides. . Dark: When you set the screen ratio to 4:3, it darkens the left and right sides. . Light: When you set the screen ratio to 4:3, it brightens the left and right sides. . To remove after images on the screen, use either All White or Signal Pattern function. Although both of the two functions remove after images on the screen, Signal Pattern is more effective. . The after image removal function has to be executed for a long time (approximately 1 hour) toeffectively remove after images on the screen. If after image is not improved after the execution of the function, repeat the function again. . Press any button on the remote control to cancel this feature. Move Enter Return .More Home Theatre PC : Off . Light Effect : Standby Mode On . Energy Saving : Off . HDMI Black Level : Low . Wall-Mount Adjustment . PIP . SetupT V Move Enter Return All White . Signal Pattern . Side Gray : Dark . Screen Burn ProtectionT V Move Enter Return Horizontal Dot : 2 . Vertical Line : 2 . Time : 2 min . Pixel ShiftT V English - 29 Setting up Your PC Software (Based on Windows XP) The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particularversion of Windows and your particular video card. But even if your actual screens look different, the same, basic set-upinformation will apply in almost all cases. (If not, contact yourcomputer manufacturer or Samsung Dealer.) 1 Right click the mouse on the Windows Desktop, then click onProperties. The Display Properties will be displayed. 2 Click on Settings tab, then set the Display Mode withreference to the Display Modes Table. You do not need to change the Colours settings. 3 Click on Advanced. A new settings dialog box will be displayed. 4 Click on the Monitor tab, then set the Screen refresh rate with reference to the Display ModesTable. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate. 5 Click on OK to close the window, then Click on OK button to the Display Properties window. Automatic re-booting may commence at this moment. English - 30 Input Mode (PC) Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display mode...
Otros modelos de este manual:TV - PS-50E92H (5.38 mb)