Votos - 1, Puntuación media: 5 ( )

Fabricar: Samsung Tamaño del archivo: 16.23 mb Nombre del archivo: Idioma del manual:

Otros manuales para este modelo:

TV - UE40C9080SW (825.71 kb)

. If the connection fails, please retry after 2 minutes. Connecting to network To setup the wireless connection automatically, follow these steps: 1. Follow Steps 1 through 3 in the “How to connect using PBC (WPS)” procedure. . If the intended network cannot be found in the list, select to open the list of networks again. 2. Select a network and connect to the network using the encryption method (PIN, security key, ad-hoc, etc.) set for the network. 3. When the network connection is complete, select Testto perform a network test. . For the automatic IP, the AP will automatically define the IPAddress,SubnetMask, Gateway and DNSserver. . For the manual IP, you can select Edit and directly enter the IPAddress,Subnet Mask,Gateway and DNSserver. . For Full Touch Control instructions, please read the Touch Control's user manual. English 9 Network Auto Configuration PBC(WPS) Select a network. Unsecured Unsecured Secured Secured 01 Getting Started Getting Started ¦ Operating specification for dual view Main TV DTV ATV Scart AV Comp. PC HDMI Touch Control DTV . . O O O O O ATV X . X X O O O SCART X X . X X X X AV X X X . X X X Comp. X X X X . X X PC X X X X X X X HDMI X X X X X X . . : and are enabled. Note that only Free channels are available for . . : enabled. Only Free channels are available. 0 : enabled. Free / Scrambled channels are available. . : enabled. X : Disabled. . Scart output: disabled when a Touch Control signal is outputted. . The Touch Control screen will freeze a few seconds while the input source of the TV switches. . A message appears saying “Not Supported Mode” if the network condition is poor. Check the network connection and try again. . or may be restricted on the touch control if one of the following functions or modes is enabled on the TV: – PVR, Media Play, Internet@TV, AllShare, or PC mode. Connecting to an Antenna When the TV is initially powered on, basic settings proceed automatically. . Preset: Connecting the mains and antenna. ANT OUTVHF/UHF Antenna Cable or 10 English Plug & Play (Initial Setup) Plug & Play (Initial Setup) 1 Turn on the TV and Touch Control. 2 Connect the Samsung Wireless LAN Adapter 3 Selecting a language 4 Selecting Store Demo or Home Use 5 Selecting a country 6 Selecting an antenna 7 Selecting a channel 8 Setting the Clock Mode 9 Time Zone 10 Viewing the HD Connection Guide. 11 Enjoy your TV. When the TV is initially powered on, a sequence of on-screen prompts will assist in configuring basic settings. Press the POWERPbutton. Plug&Play is available only when the Input source is set to TV. . To return to the previous step, press the Red button. • Turn on the Touch Control and then tap OK on your remote. . It may take about one minute to establish a wireless connection between the TV and Touch Control using the Samsung Wireless LAN Adapter. • Connect the Samsung Wireless LAN Adapter to the TV. You can connect the Samsung Wireless LAN Adapter using one of the methods shown on page 35. • If the connection fails, reconnect the Samsung Wireless LAN Adapter and then try again. Press the ^ or Ў button, then press the ENTEREbutton. Select the desired OSD (On Screen Display) language. Press the < or > button, then press the ENTEREbutton. • Select the Home Use mode. Store Demo mode is for retail environments. • To return the unit’s settings from Store Demo to Home Use (standard): Press the volume button on the TV. When the OSD volume is displayed, press and hold MENU for 5 sec. Press the ^ or Ў button, then press the ENTEREbutton. Select the appropriate country. . After selecting the country in the Country menu, some models may proceed with an additional option to setup the pin number. . When you input the PIN number, 0-0-0-0 is not available. Press the ^ or Ў button, then press the ENTEREbutton. Select Air or Cable. Press the ^ or Ў button, then press the ENTEREbutton. Select the channel source to memorise. When setting the antenna source to Cable, a step appears allowing you to assign numerical values (channel frequencies) to the channels. For more information, refer to Channel > Auto Store (p. 18). . Press the ENTERE button at any time to interrupt the memorisation process. Set the Clock Mode automatically or manually. Press the ^ or Ў button to select Auto, then press the ENTEREbutton. Press the ^ or Ў button to select the your time zone, then press the ENTEREbutton. (depending on the country) The connection method for the best HD screen quality is displayed. Press the ENTEREbutton. IfYouWant to Reset This Feature... Select Setup -Plug&Play (Initial Setup). Enter your 4 digit PIN number. The default PIN number is “0-0-0-0.” If you want to change the PIN number, use the Change PIN function. 01 Getting Started English 11 Connections Connecting to an AV Device Using an HDMI or HDMI/DVI cable (up to 1080p) Available devices: DVD, Blu-ray player, HD cable box, HD STB (Set-Top-Box) sa...

Descargar ahora

Introduzca dos números de la imagen: