Votos - 3, Puntuación media: 4.7 ( )

Fabricar: Toshiba Tamaño del archivo: 518.51 kb Nombre del archivo: Idioma del manual:

PLEASE ENTER NEW PIN CODE The numbers you enter will replace the 1122 dashes in the display. Example: To enter “1122” SELECT[0-9] END[EXIT] Press 1, 1, 2, and 2 in order. 3 After about 1 second, the display will return to the V-CHIP CONTROL menu. ENABLE BLOCKING : [Y]N SET RATING SET BLOCKING OPTIONS NEW PIN CODE BLOCK CHANNEL MOVE[t s] SELECT[T S] 32 Unblocking programs temporarily 1 If you try to watch a TV program that exceeds the rating limits you set, the TV will enter into the program block mode. THIS PROGRAM HAS BEEN BLOCKED! TV–PG L V EXCEEDS SET LIMITS PUSH MUTE TO ENTER PIN CABLE 4 2 If you want to watch the blocked program temporarily, press MUTE. Press the Number buttons (0-9) to enter the BLOCKING IS ACTIVE PLEASE ENTER PIN CODE 4-digit code you have TO TEMPORARILY UN-BLOCK ~~~– stored. If the number is correct, the block mode will be SELECT[0-9] END[EXIT] released. After 1 second, normal picture will appear. All blocking is disabled until the TV is turned off. It will be enabled when the power is reapplied. If a wrong pin code is INCORRECT PIN CODE entered, this message PLEASE ENTER PIN CODE TO TEMPORARILY UN-BLOCK appears. Enter the correct code ~~~~ again. SELECT[0-9] END[EXIT] BLOCK CHANNEL function With the CHANNEL BLOCK function, you can block specific channels. The TV will not be able to tune these channels with the CHANNEL s/t buttons or Channel Number buttons, unless you clear the setting. This TV has 8 memory spaces total, 4 for TV mode and 4 for CABLE mode. To block channels 1 Select a channel you want to block. 2 Select “BLOCK ENABLE BLOCKING : [Y]N CHANNEL” in the V-CHIP SET RATING CONTROL menu by SET BLOCKING OPTIONS NEW PIN CODE pressing t or s. BLOCK CHANNEL MOVE[t s] SELECT[T S] 3 Press T or S to display the BLOCK CHANNEL BLOCK CHANNEL menu. [SET]CLEAR 0 0 0 0 SELECT[T S] SET[t s] END[EXIT] 4 Press T or S to select BLOCK CHANNEL “SET”, then press t or s [SET]CLEAR until the channel number to 0 0 0 2 be blocked (“2” in this example) replaces “0” on the display. SELECT[T S] SET[t s] END[EXIT] 5 Repeat steps 1 to 4 for other channels. 6 Select another channel before turning off the TV. To restore channels 1 Select “CLEAR” following the above steps 2 to 4. 2 Press t or s until “0” replaces the channel numbers. BLOCK CHANNEL SET [CLEAR] 15 10 6 2 SELECT[T S] CLEAR[t s] END[EXIT] Set upPreparationBasic OperationReference Section Advanced Operation 0 0 0 0 3 Press EXIT to erase the display. 33 Set upPreparationBasic OperationAdvanced OperationReference Section Set upPreparationBasic OperationAdvanced OperationReference Section Cleaning and Care WARNING: TV sets use High Voltage. Do not try to remove the cabinet back. Refer servicing to qualified service personnel. ¦ To clean the TV screen: To maintain the finish and appearance of the cabinet, 1 . First remove the plug from the power outlet to polish it from time to time with a quality furniture avoid possible shock hazard. polish. 2 . Use a clean cellulose sponge or chamois cloth dampened with a solution of mild detergent and Caution: Never use strong solvents such as thinner, benzene or other chemicals on or near cabinet, as they might damage warm water to clean TV screen and trim. Do not the finish of the cabinet. use too much water on the TV screen. Water spills into the cabinet and may cause damage to the TV. Avoid excessive water. 3 . Remove any extra moisture with the same cloth or a dry one. 34 Specifications Television system NTSC standard Channel coverage VHF: 2 through 13 UHF: 14 through 69 Cable TV: mid band (A-8 through A-1, A through I) super band (J through W) hyper band (AA through ZZ, AAA, BBB) ultra band (65 through 94, 100 through 125) Power source 120V AC, 60Hz Power consumption 27A50: 90 W (average) 32A50: 100 W (average) 36A50: 100 W (average) Audio power 5W + 5W Speaker type 2-3/8 x 4-3/4 inches (60 x 120 mm) Audio/Video terminals S-VIDEO INPUT Y-INPUT: 1V (p-p), 75 ohm, negative sync. C-INPUT: 0.286V (p-p) (burst signal), 75 ohm AUDIO/VIDEO INPUT VIDEO: 1V(p-p), 75 ohm, negative sync. AUDIO: 150mV(rms) (30% modulation equivalent, 47k ohm) ColorStream™ (component video) INPUT Y: 1V (p-p), 75 ohm CR: 0.7 V (p-p), 75 ohm CB: 0.7 V (p-p), 75 ohm AUDIO/VIDEO OUTPUT VIDEO: 1V(p-p), 75 ohm, negative sync. AUDIO: 150mV(rms) (30% modulation equivalent, 4.7k ohm) Dimensions 27A50: Width 25-5/8 inches (652mm) Height 23-7/8 inches (600mm) Depth 20-13/16 inches (526mm) 32A50: Width 30-5/8 inches (778mm) Height 27-5/16 inches (693mm) Depth 22-11/16 inches (575mm) 36A50: Width 34-9/16 inches (878mm) Height 30-1/2 inches (774mm) Depth 25-5/16 inches (642mm) Mass 27A50: 75.0 lbs (33.6kg) 32A50: 121.7 lbs (55.2kg) 36A50: 158.0 lbs (71.6kg) Supplied accessories Remote Control with 2 size “AA” batteries Optional TV stand 27A50: — 32A50: ST3230 36A50: ST3615 Design and specifications are subject to change without notice. Set upPreparationBasic OperationAdvanced OperationReference Section 35 Set upPreparationBasic OperationAdvanced ...

Descargar ahora

Introduzca dos números de la imagen: