Fabricar: Toshiba
Tamaño del archivo: 2.26 mb
Nombre del archivo:
|
Resumen del manual
10 Connecting a camcorder Note: This connection allows you to watch videos recorded on a camcorder. If your camcorder has an S-video connection, You will need: an S-video cable will provide better picture performance than a standard video cable. • one pair of audio cables Do not connect a standard video cable and an • one video cable (see notes at right) S-video cable to Video-1 (or Video-2) at the same time or the picture performance will be unacceptable. ANT (75.) ANT-1 VIDEO 1VIDEO 2 OUT VIDEO L/MONO R AUDIO DVD IN COLOR STREAM INPUT L R AUDIO Y Pb Pr IN R S-VIDEO VIDEO L/MONO AUDIO Camcorder with S-video AUDIOVIDEO OUTL R TV Back S-VIDEO VIDEO L/MONO — AUDIO — R VIDEO-3 IN AUDIOVIDEO OUTL R TV Front Camcorder Connecting an audio amplifier This connection allows you to use an audio amplifier to adjust the audio level. This connection also allows you to use external speakers. You will need: • one coaxial cable • one pair of audio cables ToCable, Cable Box, or Antenna Audio Amplifier TV Note: To control the audio, both the TV and the amplifier must be turned on. The volume of both must be set above 0, or you will not hear any sound. See “Selecting variable audio OUT” on page 33 for additional details. IN VIDEO 1VIDEO 2 S-VIDEO VIDEO L/MONO R AUDIO OUT DVD IN COLOR STREAM INPUT L R AUDIO Y Pb Pr R VIDEO L/MONO AUDIO AUDIO L R IN OUT ANT (75.) ANT-1 Welcome toToshiba Using theRemote Control Setting upyour TV Using the TV’sFeatures Appendix Connectingyour TV 11 Using theRemote Control Using the remote control Preparing the remote control for use The remote control will operate your TV, most VCR models, and most cable TV converters, even if they are different brands. • The remote control is preprogrammed to operate most Toshiba VCRs and cable TV converters. • If you own a non-Toshiba device or a Toshiba device that the remote control is not programmed to operate, you will need to program the remote control. See “Programming the remote control” on page 13. Installing the remote control batteries To install the batteries: 1. Slide the battery cover off the back of the remote control. 2. Install two “AA” size batteries. Match the + and – symbols on the batteries to the symbols on the battery compartment. 3. Slide the battery cover back onto the remote control until the lock snaps. Using the remote control to operate a VCR or cable TV converter To control a VCR: Set the TV/CABLE/VCR switch to the VCR position. The shaded buttons in the illustration at right will then control the VCR. The unshaded buttons will operate the TV as usual. To control a cable TV converter: Set the TV/CABLE/VCR switch to the CABLE position. The shaded buttons in the top portion of the illustration at right will then control the cable TV converter. Note: The remote control provided with your TV may or may not operate certain features on your VCR, cable TV converter, or other electronic equipment. Refer to the owner’s manual provided with your other equipment to see which features are available. In addition, the other remote control may have buttons not available on your TV’s remote control. If you would like to use those features or buttons, you may need to use the original remote control provided with your other equipment. Caution: • Dispose of batteries in a designated disposal area. Do not throw batteries into a fire. • Do not mix battery types or combine used batteries with new ones. • Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment. • If you do not intend to use the remote control for a long time, remove the batteries. TV CABLE VCR MENU/ ENTER CH RTN RECALL MUTE CH CH VOL VOL 1 4 7 2 5 8 3 6 9 0 ENT100 POWER o REWPAUSE FF SOURCESTILL PIP SLOW PIP CH LOCATE SWAP STOP PLAYREC TV/VCR TV/VIDEOFAV CH A EXIT CT-90037 CHANNEL NUMBERS ENT (Used for the “Enter” command with some VCRs and cable TV converters CHANNEL y z TV/CABLE/VCR switch VCR buttons (set TV/CABLE/VCR switch to “VCR”) 12 Programming the remote control To program the remote control to operate a non-Toshiba VCR or cable TV converter or a Toshiba device the remote control is not preprogrammed to operate: 1. Refer to the VCR and cable TV converter code tables (below and on the next page) to find the code(s) for your VCR or converter. If more than one code is listed, try each one separately until you find the one that works. 2. If you are programming the remote control to operate your: •VCR: Set the TV/CABLE/VCR switch to “VCR.” •Cable TV converter: Set the TV/CABLE/VCR switch to “CABLE.” 3. While holding down RECALL, press the CHANNEL NUMBERS to enter the three-digit code for your VCR or cable TV converter brand. 4. Point the remote control at the VCR or converter, and press POWER to test the code. •If the VCR or converter responds, you entered the correct code. Note: • In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup...
Otros modelos de este manual:TV - 32AF13 (2.26 mb)