Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
4 Select the channel to rearrange, then press OK. » The selected channel is highlighted. 5 Press to move the highlighted channel to the desired location, then press OK. 6 Press OPTIONS. » [Done reordering] appears on the screen. 7 Press OK to confirm. 8 Press BACK to exit the channel grid. Test digital reception You can check the quality and signal strength of digital channels.This allows you to reposition and test your antenna or satellite dish. 1 Press MENU. 2 Press to select [Setup] > [Installation] > [Channel installation] > [Manual channel search]. 3 Press to enter the menu. 4 Press to enter the frequency of the channel you want to test. 5 Press OK to confirm the frequency, then press OK again to confirm [Search]. 6 When complete, select [Store] to store the frequency. Note • If the signal quality and streng th is poor, reposition the aerial or satellite dish and retest. • If you still have problems with the reception of your digital broadcast, contact a specialised installer. English EN 29 a TV ANTENNA 7 Connect devices This section describes how to connect devices with different connectors. Examples are provided in the Quick Star t. Note • You can use different types of connectors toconnect a device to your T V. Back connector Signal input from an antenna, cable or satellite. TV ANTENNA b EXT 1 and EXT 2 (CVBS and RGB) Analogue audio and video input from analogue or digital devices such as DVD players or game consoles. c SPDIF OUT Digital audio output to home theatres and other digital audio systems. SPDIF OUT 30 EN d SERV. U For use by ser vice personnel only. e PC IN (VGA and AUDIO IN) Audio and video input from a computer. VGA VGA AUDIO IN LEFT/RIGHT VGA/DVI f HDMI 1 Digital audio and video input from high- definition digital devices such as Blu-ray players. g EXT 3 (Y Pb Pr and AUDIO L/R) Analogue audio and video input from analogue or digital devices such as DVD players or game consoles. English Connections via DVI or VGA require an additional audio cable (see ‘Connect a computer’ on page 33). EN 31 b VIDEO Side connector Composite video input from analogue devices such as VCRs. c USB Data input from USB storage devices. d HDMI a AUDIO L/R Digital audio and video input from high- Audio input from analogue devices definition digital devices such as Blu-ray connected to VIDEO. players. 32 EN e (Headphone) Stereo audio output to headphones or earphones. f COMMON INTERFACE Slot for a Conditional Access Module (CAM). • DVI-HDMI cable EnglishAUDIO IN LEFT/RIGHT VGA/DVI DVI • HDMI cable and HDMI-DVI adaptor Connect a computer Before you connect a computer to the TV • Set the screen refresh rate on your computer to 60Hz. • Select a supported screen resolution on your computer. Connect a computer with one of the following connectors: Note • Connections via DVI or VGA require an additional audio cable. • VGA cable DVI AUDIO IN LEFT/RIGHT VGA/DVI VGA VGA AUDIO IN LEFT/RIGHT VGA/DVI • HDMI cable EN 33 Use a Conditional Access Module A Conditional Access Module (CAM) is provided by digital TV ser vice operators to decode digital TV channels. Note • Refer to the documentation from your ser vice operator on how to inser t a smar t card into the Conditional Access Module. Insert and activate a CAM Caution • Be sure to follow the instructions described below. Wrong inser tion of a CAM may damage both the CAM and your T V. 1 Switch off the TV and disconnect it from the power outlet. 2 Following the directions printed on the CAM, gently inser t the CAM into the COMMON INTERFACE at the side of the T V. 3 Push the CAM in as far as it will go. 4 Reconnect the TV to the power outlet. 5 Turn on the TV and wait for the CAM to be activated. This may take several minutes. Do not remove the CAM from the slot when in use — removing the CAM will deactivate digital services. Access CAM services 1 After inser ting and activating the CAM, press MENU. 2 Press to select [Setup] > [Features] > [Common interface]. » Applications provided by the digital TV ser vice operator appear on the screen. Note • This menu option is available only if the CAM is inser ted and activated correctly. Use Philips EasyLink Your TV suppor ts Philips EasyLink, which uses the HDMI CEC (Consumer Electronics Control) protocol. EasyLink-compliant devices that are connected through HDMI connectors can be controlled by a single remote control. Note • The EasyLink-compliant device must be switched on and selected as the source. • Philips does not guarantee 100% interoperability with all HDMI CEC devices. 34 EN EasyLink features One-touch play When you connect your TV to devices that suppor t one-touch play, you can control your TV and the devices with one remote control. One-touch standby When you connect your TV to devices that suppor t standby, you can use your TV remote control to put your TV and all connected HDMI devices in standby mode. System audio control When you connect your TV to HDMI CEC compliant devices, your TV can switch automatically to play ...