Votos - 1, Puntuación media: 5 ( )

Fabricar: Philips Tamaño del archivo: 464.82 kb Nombre del archivo: Idioma del manual:

For some programs, the title of the program will be displayed at the bottom of the screen. + Teletext keys (p.8) or VCR keys * , Sound mode (only available on stereo versions) Used to force programmes in Stereo to Mono or, for bilingual programs, to choose between Dual I or Dual II. For TV sets equipped for Nicam reception, depending on the programmes, you can force the Stereo Nicam sound to Mono or select between Nicam Dual I, Nicam Dual II and Mono. The Mono indication is red when in forced position. * “Dolby” and the double-D symbols .are trademarks of the Dolby Laboratories Licensing Corporation. Manufactured under license of Dolby Laboratories Licensing Corporation. Safety Information * VCR key The remote control lets you control the main functions of the VCR. Press and hold down the VCR key located on the side of the remote control, then press one of the keys to access the VCR functions: b%.HiIE¬P @#·.E.09 The remote control is compatible with all VCRs using the RC5 standard. • Plug the TV into a 220V – 240V AC, 50 Hz supply. • Disconnect mains plug when : – the red light below the TV screen is flashing continuously. – a bright white line is displayed across the screen. – there is a lightning storm. – the set is left unattended for a prolonged period of time. • Cleaning the TV screen. Never use abrasive cleaning agents. Use a slight damp chamois leather or soft cloth. • No naked flame sources, such as lighted candles, should be placed on top of the TV or in the vicinity. • Do not place your TV set under direct sunlight or heat. • Do not cover or block the TV as it could lead to overheating. • Leave at least 5 cm around each side of TV set to allow for proper ventilation. • Avoid placing your set (e.g. near the window) where it is likely to be exposed to rain or water. • Battery Usage CAUTION – To prevent battery leakage that may result in bodily injury, property damage, or damage to the unit: – Install all batteries correctly, with + and – aligned as marked on the unit. – Do not mix batteries (old and new or carbon and alkaline, etc.). – Remove batteries when the unit is not used for a long time. Useful Tips • Do not leave your set on standby mode for a prolonged period of time. Switch off set to allow it to be demagnetised. A demagnetised set supports good picture quality. • Do not shift or move the set around when it is switched on. Uneveness in colour in some parts of the screen may occur. • Never attempt to repair a defective TV yourself. Always consult a skilled service personnel. 3 L01_15524 (GB) 1-1_190705 7/19/05 3:55 PM Page 4 Quick installation The first time you switch on the television, a search and the number of programs found. menu appears on the screen and the tuning At the end of the search, the menu disappears. starts automatically. To exit or interrupt the search, press H. Auto Store • Program 2 • TV 470 MHz • •••••••••••••••••••••••••••••••• If the menu is not displayed, press and hold down the ”- and ”+ keys on the TV set for 5 seconds to start the tuning. All the available TV programs and radio stations * will be stored. This operation takes a few minutes.The display shows the progress of the If no program is found, consult the possible solutions p. 12. & If the transmitter or cable network sends the automatic sort signal, the programs will be numbered correctly. In this case, the installation is complete. e If this is not the case, you need to use the Sort menu to number the programs correctly. Some transmitters or cable networks broadcast their own sort parameters (region, language, etc.). In this case, indicate your choice using the iI keys and validate with ¬. * Only on versions equipped with a radio. Program sort & Press key H.The Main menu is displayed on e With the cursor, select the Install menu the screen. followed by the Sort menu. Mainge • Picture • Sound • Features $ Install Install • Language • Country • Auto Store • Manual Store $ Sort . • Name 00 01 TF1 02 FR2 03 . FR3 04 C + 05 ARTE “ Select the programme you want to move using the iI keys and press ¬. ‘ Then use the iI keys to select the new number and validate with E. ( Repeat steps “ and ‘ for each program you wish to renumber. § To quit the menus, press d. Program name If required, you can give a name to the programmes and external connectors. Note: on installation, the programs are named automatically when an identification signal is sent. & Press the H key. e With the cursor, select the Install menu, then Name “ Use the iI keys to select the programme to name or rename. ‘ Use the E¬ keys to move around the name display area (5 characters) and the iI keys to select the characters. ( When the name has been entered, use the E key to exit.The name is stored. § Repeat steps “ to ( for each programme you wish to name. e To quit the menus, press d. 4 L01_15524 (GB) 1-1_190705 7/19/05 3:55 PM Page 5 Manual store This menu is used to store the programmes one at a time. & Press the H key. e With the cursor, select the ...

Descargar ahora

Introduzca dos números de la imagen: