Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Place the TV on a solid surface. For ventilation, leave at least 5 cm free all around the TV. To prevent any fault and unsafe situation, please do not place any objects on top of the TV. Insert the aerial plug tightly into the aerial socket g at the back of the TV with an aerial cable of good quality. CABLE 4 Check if the loudspeaker switch at the back of the TV is in the l position. Remote control Remove the cover of the battery compartment on the back of the remote control. Insert the 2 batteries supplied (Type R03G/AAA-1,5V). Click the cover back into place. The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless in many countries exhausted batteries may not be disposed of with your household waste. Please inform yourself on how to dispose of exhausted batteries according to local regulations. 4 Press the TV key next to the display. 5 In the display of the remote control the letters TV appear in a black block for a few seconds. You can now operate your TV with the remote control. VCR 1 VCR 2 SAT AMP TUNER TAPE DCC CD M 0 a KK B OKMENU B B B B TV TV R03G/AAA English 3 Connect your computer 4 Connect one end of the supplied S/VGA cable to the video card of the computer and the other end to the S/VGA IN connector at the rear side of the TV set. 4 Fix the connectors firmly with the screws on the plug. Connect your Apple Macintosh* computer Attention: Macintosh computers with separate H and V synchronisation signals can be used together with the supplied adapter. Macintosh computers with Composite Sync and Sync on Green signals may need a special (not supplied) adapter or cable. Contact your dealer. < Connect the supplied switchable adapter for Apple video connectors to one end of the supplied S/VGA cable. < Put the DIP switches on the adapter in the following positions : 1 2 off off < Connect the end of the S/VGA cable with the adapter to the video card of the computer and the other end to the connector on the back of the TV. < Screw the connectors down firmly. SVGA IN SVGA OUT RS L R A/V 1 IN L L R AUDIO S-VHS VIDEO VIDEO DIO UT R a 15-pin D sub 15-pin mini D sub (2-row) (3-row) < The supplied audio cables can be connected to the audio outputs of your Multimedia computer and to the AUDIO R (right) and L (left) inputs below the S/VGA IN connector. To reproduce computer screen information and/or programmes, see p. 32. 4 * Apple Macintosh is a registered trademark of Apple Computer, Inc. DDC Plug and Play The S/VGA display supports Plug and Play facilities (DDC 1 or 2 B) as available in Windows 95. Note: the graphical board of your computer should be fit for Plug and Play. RS-232 port This TV has an RS-232C connection for PC control with an RS-232 signal cable. Please contact your local Philips organisation for details. Daisy chaining The Active Loop Thru facility makes it possible to make a daisy chain (max. 4 TVs). Connect the TVs before inserting the mains plug in the wall socket. 4 Connect another S/VGA cable to the S/VGA OUT connector of the TV and to the S/VGA IN connector of a second S/VGA TV. In case of a Multimedia computer, also connect the audio cables to the audio inputs R (right) and L (left) above the S/VGA OUT connector and to the audio S/VGA IN S/VGA OUT S/VGA IN S/VGA OUT S/VGA IN inputs of the second S/VGA TV. Computer Display modes • VGA 640x480 31.468kHz 60Hz • VGA 640x400 31.468kHz 70Hz • VGA 640x350 31.468kHz 70Hz • SVGA 800x600 35.156kHz 56Hz • MAC Z 640x480 35.000kHz 67Hz When a VGA computer is connected, the selection is made automatically. When a S/VGA or Macintosh computer is connected, make a selection yourself between PC or MAC Z. See Install TV Configuration, Computer, p. 12. Insert the mains plug in the wall socket with a mains voltage of 220V-240V. English 5 Switch TV on 4 Press the power switch A on the front of your set. 5 A green or red lamp lights up on the front of your set. green ................................................... or red ..................................................................... 5 The TV is on. 5 The TV is switched on but the screen stays The screen lights up after a few moments. dark. Your TV is on standby. 4 Press a digit key or the red standby key B on the remote control. 5 The TV is on. The screen lights up. 5 The green lamp blinks every time you press a key on the remote control. Switch menus on and off 4 Press MENU on the remote control. 5 The MAIN MENU appears. 4 Use the keys V or W to make a selection of the Main Menu items. 5 Your selection lights up. 4 Press the OK key on the remote control to activate the selected menu. 4 Press MENU again to return to the previous menu. 4 Keep the MENU key pressed to switch off all menus. Select the menu language You can now choose which language the menus are presented in. Menu Language Country Automatic Installation Manual Installation Give Name Reshuffle Favourite Programmes TV Configuration Decoder/Descrambler English ••• ••• ••• ••• ••• ••• ••• ••• 4 Press MENU on...
Otros modelos de este manual:TV - 29PX8001/01 (589.78 kb)