Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
This option selects the initial picture mode appropriate for the typical lighting condition in these environments. 7: Auto-tuning the TV 1 Press . 2 Press F/f to select “Antenna” or “Cable”, then press . If you select “Cable”, the screen for selecting the scan type appears. See “z” (page 7). The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding. If a message appears for you to confirm the aerial connection No digital or analogue channels were found. Check all the aerial/cable connections and press to start auto-tuning again. 3 Programme Sorting (Only in analogue mode): Changes the order in which the analogue channels are stored on the TV. 1 Press F/f to select the channel you want to move to a new position, then press g. 2 Press F/f to select the new position for your channel, then press . If you do not change the order in which the analogue channels are stored on the TV, press HOME to go to next step. ~ • This step will not appear if any analogue channel is found. The message "Set-up complete" will appear on the screen. Press . The TV has now tuned in all the available channels. z • System Update You can update the TV system using USB memory. Obtain information from the website below. To tune the TV for Cable connection 1 Press . 2 Press F/f to select “Quick Scan” or “Full Scan”, then press . "Quick Scan" : channels are tuned according to the cable operator information within the broadcast signal. Recommended setting for "Frequency" and "Network ID" is "Auto". This option is recommended for fast tuning when supported by your cable operator. If the "Quick Scan" does not tune, please use the "Full Scan" method below. "Full Scan" : All available channels are tuned and stored. This procedure may take some time. This option is recommended when "Quick Scan" is not supported by your cable provider. For further information about supported cable providers, refer to support web site: 3 Press G/g/f to select “Start”. The TV starts searching for channels. Do not press any buttons on the TV or remote. ~ • Some cable providers do not support “Quick Scan”. If no channels are detected using “Quick Scan”, perform “Full Scan”. Start-up 7 GB Adjusting the viewing angle of the TV Adjusting the viewing angle of the TV (only for KDL-40/32NX5xx) Adjust the angle left and right (swivel) Top view Front (only for KDL-22EX3xx) Adjust the tilt 0. 8. 8. Detaching the Table- Top Stand from the TV ~ • Do not remove the Table-Top Stand for any reason other than to wall-mount the TV. Table-Top Stand Table-Top Stand (only for KDL-22EX3xx ) z • Be sure the TV is on the vertical position before switching on. TV set must not be powered on with LCD panel face down to avoid uneven picture uniformity. 8 GB SafetyInformation SafetyInformation Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries. Installation • The TV set should be installed near an easily accessible mains socket. • Place the TV set on a stable, level surface. • Only qualified service personnel should carry out wall installations. • For safety reasons, it is strongly recommended that you use Sony accessories, including: – Wall-mount bracket SU-WL500 (KDL-46EX4xx, KDL-40BX4/EX4/ EX6/NX5xx, KDL-37EX4xx, KDL32BX3/ BX4/EX3/EX4/EX6/NX5xx) – Wall-mount bracket SU-WL100 (KDL-26EX3xx, KDL-22EX3xx) • Be sure to use the screws supplied with the Wall-mount bracket when attaching the mounting hooks to the TV set. The supplied screws are designed so that they are 8 mm to 12 mm in length when measured from the attaching surface of the mounting hook. The diameter and length of the screws differ dependi...
Otros modelos de este manual:TV - KDL-32BX300 (1.81 mb)
TV - KDL-32BX400 (1.81 mb)
TV - KDL-40BX400 (1.81 mb)
TV - KDL-26EX301 (1.81 mb)