Votos - 4, Puntuación media: 3.8 ( )

Fabricar: Sony Tamaño del archivo: 2.2 mb Nombre del archivo: Idioma del manual:

Refer to “To use i-Manual” for operation (page 9). • Before operating the TV, please read “Safety Information” (page 16). Retain this manual for future reference. Checking the accessories Inserting batteries into the remote AC power cord (mains lead) (1) Cable holder (1) Remote (1) Size AAA batteries (R3 type) (2) Table-Top Stand (1)*1 Fixing screws for Table-Top Stand (M5 . 16) (4) Assembling screws for Table-Top Stand (M5 . 16) (4) (KDL-40HX803 only) Stand rear cover (1)*2 *1 For KDL-40HX803, assemble the Table-Top Stand with the supplied assembling screws. Refer to the supplied Table-Top Stand leaflet to assemble the stand. *2 For KDL-46HX803, the stand rear cover is 1Remove the protection sheet. 2Push and slide the cover upward. factory-attached to the Table-Top Stand. 3 GB Adjusting the viewing angle of Adjusting the viewing angle of the TV (KDL-52/46HX903 only) Stand This TV can be adjusted within the angles 1 Refer to the supplied Table-Top Stand shown below. leaflet for proper attachment for some TV models. 2 Place the TV set on the Table-Top Stand. 3 Fix the TV to the Table-Top Stand according to the arrow marks that guide the screw holes using the supplied screws. ~ 1 4 6.0. Remove screw as Install screw into • If using an electric screwdriver, set the tightening shown. the top screw hole torque at approximately 1.5 N·m {15 kgf·cm}. of the Table-Top 4 For KDL-52/46HX903 and KDL40HX803, after all the screws are tightened, attach the supplied stand rear 2 3 cover to the Table-Top Stand. Stand. Slide in. Lift up and tilt. ~ • To return to 0°, reverse the above procedure. 4 GB Setting Connecting an antenna (aerial)/Set Top Box/ recorder (e.g. DVD recorder) Connecting a Set Top Box/recorder (e.g. DVD recorder) with SCART Preventing the TV from toppling over 1 Install a wood screw (4 mm in Set Top Box/recorder (e.g. DVD recorder) Setting Connecting an antenna (aerial)/Set Top Box/ recorder (e.g. DVD recorder) Connecting a Set Top Box/recorder (e.g. DVD recorder) with SCART Preventing the TV from toppling over 1 Install a wood screw (4 mm in Set Top Box/recorder (e.g. DVD recorder) (e.g. DVD recorder) with HDMI Set Top Box/recorder (e.g. DVD recorder) diameter, not supplied) in the TV stand. 2 Install a machine screw (M4 . 16, not supplied) into the screw hole of the TV. 3 Tie the wood screw and the machine screw with a strong cord (not supplied). 5 GB 6 GB Bundling the cables ~ • Do not bundle the AC power cord (mains lead) together with other cables. Performing the initial set-up 1 Connect the TV to your AC power outlet (mains socket). 2 Check the ENERGY SAVING SWITCH setting is on (z). 3 Press 1 on the TV. When you switch on the TV for the first time, the Language menu appears on the screen. Follow the instructions on the screen. Digital Auto Tuning: When you select “Cable”, we recommend that you select “Quick Scan” for quick tuning. Set “Frequency” and “Network ID” according to the information supplied from your cable provider. If no channel is found using “Quick Scan”, try “Full Scan” (though it may take some time). For a list of compatible cable providers, refer to the support web site: DVBC/ 4 Programme Sorting: Changes the order of analogue channels stored in the TV. Programme Sorting: Changes the order of analogue channels stored in the TV. 2 Press F/f to select the new position for the channel, then press . ~ • You can also tune channels manually. Detaching the Table-Top Stand from the TV ~ • For KDL-52/46HX903 and KDL-40HX803, remove the stand rear cover prior to detaching the Table-Top Stand. • Remove the screws guided by the arrow marks of the TV. • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the TV. • Do not hold by the stand rear cover while carrying the Table-Top Stand to prevent dropping the stand which may cause an injury or damage to the property. Setting 7 GB Watching TV To watch programmes 2 GUIDE OPTIONS HOME 3 z • The number 5, N, PROG + and AUDIO buttons on the remote have a tactile dot. Use the tactile dots as a reference when operating the TV. 1 Turn on the TV. 1 Switch ENERGY SAVING SWITCH on (z). 2 Press 1 on the TV to turn on the TV. 2 Select a mode. 3 Select a TV channel. Using Digital Electronic Programme Guide Press GUIDE in digital mode to display the programme guide. To utilise the TV’s features HOME button Press to display various operation and setting screens. OPTIONS button Press to display convenient functions based on the current input or content. Settings TV System Settings Picture Sound SCART REC on Add t F urit L ck/Unlock PAP Motionflo Scene S lec Sleep Timer Headphone V lume Speak 8 GB To use i-Manual 1 2 To use i-Manual 1 2 x Welcome to i-Manual x Fun Features with Connected Equipment x “BRAVIA” TV Features Introduces how to connect optional equipment. x Watching TV x Parts Description Introduces convenient features such as EPG Guide, Favourites, etc. x Troubleshooting F...

Descargar ahora

Introduzca dos números de la imagen: