Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
IF NOT, THE WALL STRUCTURE MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY. WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. Indicates that the power plug is to be Contact Premier Mounts with any disconnected from the power outlet. questions. Safety precautions must be taken at all times. Warning and Caution statements. Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the flat panel display and/or damage to the mounting surface. Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the flat panel display and could increase the risk of fire. At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the flat panel display. Page - 4 -Installation Manual CTM-MS2 Parts List NOTE: This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700). WM4000 Wall Plate (Qty 1) Mounting Brackets (Qty 2) 5/16” Flat Washers (Qty 6) 5/16” x 3” Lag Bolts (wooden studs only) – (Qty 6) M6 x 30mm Lateral Shift Locking Screws (Qty 2) Griplates™ (Qty 8) M6 x 12mm Safety Knobs (Qty 2) Thread Depth Indicator Installation Tools Phillips Head Screw Driver Soft Material/ Blanket 5/16” Socket and Wrench Pencil Tape Measure Drill Gun Level (Supplied) Installation Manual Page - 5 - CTM-MS2 Page - 6 - Installation Manual M4 x 25 M5 x 20 M5 x 50 M8 x 20 M6 x 30 (Qty 6) (Qty 4) (Qty 6) (Qty 4) (Qty 2) M4 x 16 (Qty 8) M5 x 12 (Qty 8) M5 x 16 (Qty 6) M5 x 25 (Qty 4) M6 x 12 (Qty 8) M8 x 25 (Qty 6) M8 x 30 (Qty 6) M8 x 35 (Qty 4) M6 x 20 (Qty 6) M8 x 70 (Qty 4) CTM-MS2 Nylon spacers and flat washers actual size NOTE: The nylon spacers may be stacked to achieve proper spacing. 1/4" Nylon spacers 5/16" Flat washers (metal) 1" Nylon spacers 1/4" Nylon spacers (large) (small) 1/2" Nylon spacers (large) (Qty 6) (Qty 12) (Qty 6) (Qty 6) (Qty 6) 9/16" Nylon spacers (Qty 6) Nylon sleeves (Qty 4) Installation Manual Page - 7 - CTM-MS2 Page - 8 - Installation Manual Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). 3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw. 4. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3), until you find one that comes closest to your mark without going past. Figure 1 Figure 2 Figure 3 Marking the depth Thread depth indicator Thread insert Inverted flat panel display Screw Marking Thread depth indicator Screw Thread depth indicator Marking CTM-MS2 Mounting Bracket Installation NOTE: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING: INVERT THE FLAT PANEL PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC. ...