Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the display. Contact Premier Mounts with any technical/installation questions. Page 2 Installation Instructions RTM-C Parts List NOTE: The RTM-C may be used with the RTM-L or the RTM-S Series Display Mounts. It is imperative that the installation instructions be read for these mounts prior to installation. The installation instructions that are contained herein are exclusively for the RTM-C. NOTE: This adapter is shipped with all installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop and contact Premier Mounts (800) 368-9700. RTM-C (Qty 1) M8 x 20mm Button Hex Head (Qty 4) M3 Allen Wrench (Qty 1) M5 Allen Wrench (Qty 1) M6 x 10mm Phillips Head Screw (Qty 1) Cable Ties (Qty 2) Installation Tools Phillips Head Screw Driver Soft Material/Blanket Pencil Tape Measure M5 Allen Wrench (Supplied) M3 Allen Wrench (Supplied) Installation Instructions Page 3 RTM-C Attaching the RTM-C to the RTM NOTE: The installation instructions that are contained in this manual refer only to the RTM-C. The installation instructions for optional configurations (page 7) that are used with the RTM-C will be included with those products. NOTE: Prior to installing the RTM-C, the RTM-C must be attached to the RTM-L or the RTM-S. 5/32” Allen Wrench 1. Remove the set screws from the mounting block on your Rotary Series Mount (two are located on each side of the mounting block) Mounting using the 5/32” Allen wrench (supplied with Block the RTM-S and the RTM-L). Set Screw 2. Place the RTM-C (flat edge facing the rear) onto the RTM and line up the mounting holes. Flat Edge 3. Insert four (4) M8 x 20mm button hex head M8 x 20mm screws into the mounting and tighten Button Hex using the M5 Allen wrench (supplied). Head Screws RTM-C M5 Allen Wrench 4. After tightening the M8 x 20mm button hex head screws, place the RTM-C to the side and determine where the suspension pole will be installed. NOTE: Please refer to the installation instructions that are included in the packaging of the mount that will be used for the next steps. Page 4 Installation Instructions RTM-C Attaching the RTM-C to the Suspension Pole Once the mounting configuration has been determined and installed, the RTM-C may be attached. NOTE: Depending on the installation configuration, a 1-1/2” NPT must be installed prior to installing the RTM-C. NOTE: It is recommended tthe suspension pipe, the other person must hohat two people install theld the ladder. RTM-C. While one person attaches the RTM-C onto Threaded Pipe Cable Management Holes 1. Place the RTM-C coupler onto the threaded end of the suspension pole. Thread the coupler onto the threaded pipe tighten at least seven (7) complete turns. RTM-C 2. After the RTM-C has been threaded onto the 1-1/2” NPT, tighten the M6 x 10mm set screw using a M3 Allen wrench (supplied). 3. Use the cable management holes, along with the cable ties, to secure and hide any loose cables and wires. M3 Allen Wrench M6 x 10mm Set Screw Cable Management Holes Installation Instructions Page 5 RTM-C Optional Configurations You may use the RTM-C with the following optional accessories. Please refer to the Installation Instructions that come packaged with the following products. AST-2446 APP-2446 AST-1321 Technical Specifications All measurements are in inches (mm). Page 6 Installation Instructions RTM-C PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor costs. What is Not Covered; Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS. PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. What C...