Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the display and/or damage to the mounting surface. Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the display and could increase the risk of fire. At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the display. Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available). Contact Victory Mounts with any technical/installation questions. 9531-015-122-06 Included Hardware Universal Washer (Qty 8) 3” Lag Bolts (Qty 6) Flat Washers (Qty 6) To correctly determine your hardware, please refer to the hardware list below. 1/4" Nylon spacers 5/16" Flat washers (metal) 9/16" Nylon spacers (large) 1/2" Nylon spacers (large) Nylon sleeves (Qty 6) (Qty 12) (Qty 6) (Qty 6) (Qty 4) 1/4" Nylon spacers (small) (Qty 6) M4 x 25 M5 x 20 M5 x 50 M8 x 20 M4 x 16 (Qty 8) M5 x 12 (Qty 8) M5 x 16 (Qty 6) M5 x 25 (Qty 4) M6 x 12 (Qty 8) M8 x 25 (Qty 6) M8 x 30 (Qty 6) M8 x 35 (Qty 4) M6 x 20 (Qty 6) M8 x 70 (Qty 4) M6 x 30 (Qty 6) (Qty 4) (Qty 6) (Qty 4) (Qty 6) Tool List Phillips Head Screw Driver Electronic Stud Finder .” Socket and Wrench Portable Drill Masonry Bit for Concrete Installation 1/4” Drill Bit for Wood Installations Level (Commercially Available) Wood Stud Mounting 1. For secure wood stud mounting, the wall plate must be mounted to two studs at least 16” apart. 2. Use a high-quality electronic stud finder (commercially available) to locate two adjacent studs and mark their locations with a pencil. 3. With the help of an assistant, use a level (commercially available) and position the wall plate against the wall in the desired mounting location. 4. Mark the right, upper and lower and the left (upper and lower), positions of the small horizontal slots that are in alignment with the studs. 5. You should mark four positions total. 6. Next, pre-drill a 1/4” hole in the wall stud at each marked location. Continued on back page Lag Bolt and Washer Continued from front page 7. With the help of an assistant, position the wall plate against the wall and line up the mounting slots with drilled holes. 8. For each location, insert a lag bolt and washer into the wall. 9. Tighten each bolt with an open ended socket wrench by turning clockwise until tight. Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. Do not release the wall plate until it is properly mounted and secured to the wall. Concrete Mounting The concrete anchors must be used for concrete installation. They can be purchased at your local hardware store. 1. Begin by placing the wall plate into position against the wall, using the bubble guide to keep it level. 2. Mark off six holes to be used for securing the mount and place the wall plate aside. 3. Next, drill holes using an electric drill and masonry bit. 4. Insert a concrete anchor into each hole. 5. If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the wall. 6. Once all of the anchors are in place, move the wall plate back into position. 7. Attach the nut onto the threaded shaft that is protruding from the wall. 8. Do not tighten until all nuts are in place. How to Determine Thread Depth Inverted Flat Panel Display Marking the Depth Thread Insert Thread Depth Indicator Screw Marking Stir Straw or Toothpick Screw Marking Stir Straw or Toothpick Figure 1 Figure 2 Figure 3 Display Bracket Installation 1. To ensure optimal installation, this kit includes various screws of different diameters and lengths. 2. Place your flat panel screen down on a soft, flat surface, and locate the threaded mounting points that are located on the back of the display. 3. Determine which screw is the correct length by carefully inserting a straw, or toothpick, and mark how deep the mounting point is. 4. If your display has a curved back or a recessed thread mounting point, a spacer must be used. Select the spacer that is closest in depth to the recess to keep your bracket as close to the display as possible. 5. Place the spacer between the mounting bracket and the display. 6. If a smaller screw is being used (M4, M5, or M6) please use a square griplate with each screw for added stability. 7. Attach each bracket to the display by aligning the holes on each bracket, with the threaded inserts on the back panel of your display, inserting the screws through both and turning clockwise until they are fully inserted. 8. Tighten with a Phillips head screw driver. Final Installation Two people are required for this step. MAKE SURE THE LOCKING SCREW IS FLUSH WIT...