Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS. THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE DISPLAY. IF NOT, THE MOUNTING STRUCTURE MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN INSTALLATION , AS OUTLINED IN THE INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY. At least two qualified people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the display. If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is recommended. Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in wall. Cutting/drilling into an electrical line may cause serious injury. Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water damage to the mounting surface. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact Contact Premier Mounts with any questions (800) 368-9700 techsupport@mounts.com Page 2 Installation Instructions AM250 Installation Instructions Page 3 Parts List This mount is shipped with all installation hardware and components. Make sure that none of these parts are missing and/ or damaged before beginning installation. If there are parts missing and/or damaged, please stop and contact Premier Mounts (800) 368-9700. Installation Tools Phillips Head Screw Driver Soft Material/ Blanket 1/2" Socket and Wrench Pencil Tape Measur e Drill Gun Level (Supplied) Thread Depth Indicator (Supplied) ." Drill Bit (Pilot Holes) Masonry Drill Bit (Concrete Applications - Commercially Available) Swingout Arm (Qty 1) 5/16" Flat Washers (Qty 6) 5/16" x 3" Lag Bolts (wooden studs only) (Qty 6) Universal Mounting Bracket (Qty 2) Griplate™ (Qty 8) AM250 Page 4 Installation Instructions M4 x 16 (Qty 8) M5 x 12 (Qty 8) M5 x 16 (Qty 6) M5 x 25 (Qty 4) M6 x 12 (Qty 8) M8 x 25 (Qty 6) M8 x 30 (Qty 6) M8 x 35 (Qty 4) M6 x 20 (Qty 6) M8 x 70 (Qty 4) M4 x 25 M5 x 20 M5 x 50 M8 x 20 M6 x 30 (Qty 6) (Qty 4) (Qty 6) (Qty 4) (Qty 6) Parts List (Cont.) Installation Instructions Page 5 AM250 Parts List (Cont.) Nylon spacers and flat washers' actual size. The nylon spacers may be stacked to achieve proper spacing. 5/16" Nylon sleeves (Qty 4) 1/4" Nylon spacers 5/16" Flat washers (metal) 1" Nylon spacers 1/4" Nylon spacers 9/16" Nylon spacers (large) (small) 1/2" Nylon spacers (large) (Qty 6) (Qty 12) (Qty 6) (Qty 6) (Qty 6) (Qty 6) AM250 Thread Depth Indicator Step 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). Step 2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). Step 3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw. Step 4. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3), until you find one that comes closest to your mark without going past. Figure 1 Thread Depth Indicator Marking Screw Marking Screw Thread Depth Indicator Inverted Flat Panel Display Marking the Depth Thread Insert Thread Depth Indicator Figure 3 Figure 2 Page 6 Installation Instructions AM250 Mount Installation THE FOLLOWING STEPS SHOULD BE PERFORMED BY TWO PEOPLE. For ease of installation, it is recommended that two people perform the installation. One person should hold the mount while the other person installs the lag bolt and washer. Making sure that the mount is level, the person not holding the mount must mark and drill the second mounting hole and secure the second lag bolt and washer. If the studs are 12” apart, use three 3” lag bolts for the top row of mounting points and three 3” lag bolts for the lower row mounting points. If the studs a...
Otros modelos de este manual:TV - AM250 (4.84 mb)