Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Use the arrow buttons to select a character, then press the Enter button. When you have selected all of the characters in your name, select Finish and press the Enter button. Deleting Saved Memory Settings You can clear all your memory settings at once. 1. Press the Menu button on the remote control. 2. Open the Reset menu, then select Reset Memory. 3. Select Yes, then press the Enter button to delete the memory settings. Note: You can delete memory settings one at a time with the Erase Memory setting under the Memory menu. Making Detailed Adjustments 43 Resetting the Projector If the image quality isn’t what you expect, one or more settings may be adjusted improperly. If necessary, you can restore the projector to its factory-default (original) settings. To restore the settings in a specific menu (such as the Image or Settings menu), open that menu, select Reset, and confirm as needed. The example below shows how to reset the Image menu settings: Open the Image menu . . . and select Reset You can also reset the lamp usage timer or restore all the projector settings to their original values. Follow these steps: 1. Press the Menu button on the remote control. 2. Open the Reset menu. 3. Do one of the following: ¦ Select Reset Lamp Hours to clear the lamp usage timer and reset it to zero. You should reset the lamp timer only when you install a new projector lamp. See page 55 for more information. ¦ Select Reset Memory to clear all memory settings. ¦ Select Reset All to return all projector settings to their original defaults (except Component, Save Memory, Language, and Lamp). 44 Making Detailed Adjustments Customizing Projector Features Use the settings in this section to adjust the image size and position, suppress on-screen text, and select basic setup options. Image Sizing Before adjusting any of these settings, make sure you have already selected an appropriate aspect ratio for the type of picture you’re viewing (see page 28). ¦ Output Scaling Signal > Advanced > Output Scaling For component video formats, this setting lets you see the edges of the image that are not normally visible in the picture (see page 67). If you see interference when you set Output Scaling to 100%, try adjusting the Position as described below. ¦ Position Signal > Position Note: This setting cannot be used with a signal input through the HDMI 1 or HMDI 2 port. Use the arrow buttons to fine-tune the position of the image on the screen. ¦ Aspect Signal > Aspect This setting lets you change the aspect ratio of your image, and works the same as pressing the Aspect button on the remote control. See page 28 for more information. ¦ Zoom Caption Pos. Signal > Zoom Caption Pos. Lets you adjust the shape and position of the image so that subtitles are visible (available only if the aspect ratio has been set to Zoom). Use Zoom Size to adjust the proportions of the image, and Zoom Caption Pos. to move the image up or down. You can adjust output scaling before zoom position. Making Detailed Adjustments 45 Screen Options ¦ Messages Settings > Display > Messages Turn this setting off if you want to prevent on-screen messages from appearing (such as the no-signal message, or the identifying text that appears when you switch between image sources or color modes). ¦ Startup Screen Settings > Display > Startup Screen Turn this setting off if you want to prevent the startup screen from appearing while the projector is warming up. ¦ Display Background Settings > Display > Display Background Changes the screen that’s used when the projector is not receiving a signal or when you press the Blank button to temporarily stop projection. Other Setup Options ¦ Projection Settings > Projection You can select different options for projecting the image: Front, Front/Ceiling, Rear, Rear/Ceiling. ¦ Direct Power On Settings > Direct Power On Sets projection to start when the main power switch is turned on, without pressing the P power button on the remote control or the projector. Note: When direct power on is enabled, power surges that occur after a power outage can cause the projector to turn on. ¦ Video Signal Settings > Input Signal > Video Signal Leave this setting on Auto so the projector can automatically interpret the format, such as NTSC or PAL (for standard TV formats). 46 Making Detailed Adjustments ¦ Component Settings > Input Signal > Component Change this setting to match the type of equipment connected to the Component port. For component video, select Auto to let the projector automatically interpret the signal; or select YCbCr or YPbPr to manually select your video equipment’s signal. ¦ Trigger Out Settings > Trigger Out Turn on this setting if you want the Trigger out port to output a 12-volt signal while the projector is operating. You can use this to raise or lower your projection screen. Note: If you change this setting, the new setting will take effect the next time you turn the projector on. ¦ Sleep Mode Settings > Sleep Mode Turn off this se...