Votos - , Puntuación media:
(
)
)
Fabricar: Omnimount
Tamaño del archivo: 523.42 kb
Nombre del archivo: 55a2238a-f735-47fb-9da2-3ba0c969a7a7.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
(See illustration • This mount will only fit and securely mount speakers with 6mm pre-threaded inserts. If you are unsure about the insert, please contact the speaker manufacturer. Before You StartBefore You StartBefore You StartBefore You StartBefore You Start Read This Section CarefullyRead This Section CarefullyRead This Section CarefullyRead This Section CarefullyRead This Section Carefully To use the 5.0 Speaker Mount Kit, your speaker must meet the following criteria: Your speaker must have a factory-installed 6mm threaded insert. We have found that most of the factory inserts installed for mounting are strong enough to safely support the speaker. However, some inserts located on the top, bottom, or sides of the speaker are designed to be used in pairs for attaching a “U-shaped” bracket to the speaker. When one of these two inserts is used alone it may not have adequate pullout strength to support the weight for the speaker in some cases. If you have any questions regarding the use of the inserts in your speaker, consult your dealer or contact the speaker manufacturer directly. Note: Use the supplied screws and anchors. Your 5.0 Mount is supplied with oversize surface mounting screws and anchors. The generous size of these fasteners provides an extra margin of safety for your installation. Do not use substitutes. The ball shaft-threads into the speaker. The clamp assembly- Consists of the clamp plate and jaw. It mounts to the wall, ceiling or a shelf. The clamp surrounds the ball. The mounting angle may be adjusted by simply loosening the clamp assembly tension screw. TTTTTools Requiredools Requiredools Requiredools Requiredools Required You will need at least these tools for the installation • 5/32” hex wrench (supplied) • An electric drill • Drill bits: .” (for drywall installation) or 5/16” (for wood and masonry surfaces) • 7/16”(11mm) open wrench or small crescent wrench • Phillips screwdriver, medium size (or electric drill with Phillips drive bit) • Wire cutters • Hammer KIT COMPONENTS & HOW THEY WORK TOGETHER:KIT COMPONENTS & HOW THEY WORK TOGETHER:KIT COMPONENTS & HOW THEY WORK TOGETHER:KIT COMPONENTS & HOW THEY WORK TOGETHER:KIT COMPONENTS & HOW THEY WORK TOGETHER: Mounting OptionsMounting OptionsMounting OptionsMounting OptionsMounting Options Before you begin, decide which mounting option and ball shaft areBefore you begin, decide which mounting option and ball shaft areBefore you begin, decide which mounting option and ball shaft areBefore you begin, decide which mounting option and ball shaft areBefore you begin, decide which mounting option and ball shaft are appropriate for your speakerappropriate for your speakerappropriate for your speakerappropriate for your speakerappropriate for your speaker..... Step 1:Step 1:Step 1:Step 1:Step 1: Attaching the Ball Shaft to the SpeakerAttaching the Ball Shaft to the SpeakerAttaching the Ball Shaft to the SpeakerAttaching the Ball Shaft to the SpeakerAttaching the Ball Shaft to the Speaker • Insert the ball shaft appropriate to the mounting option you have selected (refer to the mounting options above). • Rotate the ball shaft several turns until it is fully threaded into the female insert on the speaker. When you “hit bottom”, back out the ball shaft approximately one quarter turn (see Fig. E). • Using the 7/16” (11mm) open wrench, tighten the jam nut. CAUTION: DO NOT OVER-TIGHTEN. When the ball shaft resists moderate rotational force and forms a solid joint with the speaker, stop tightening. Fig. E Step 2:Step 2:Step 2:Step 2:Step 2: Positioning the Clamp AssemblyPositioning the Clamp AssemblyPositioning the Clamp AssemblyPositioning the Clamp AssemblyPositioning the Clamp Assembly 2.12.12.12.12.1 Wall mounting Orient the clamp assembly vertically—the OmniMount logo should be facing toward the ceiling, the tension screw head faces toward the floor (see fig. G or H) CAUTION: It may be necessary to check that the surface preparation and the fasteners will not interfere with electrical wiring, plumbing, etc., behind your mounting surface (wall, ceiling, floor). 2.22.22.22.22.2 Ceiling or shelf mounting orientation The clamp assembly should be oriented so that the clamp plate and OmniMount logo face the same direction as the front of the speaker you are mounting. The jaw and the tension screw will face in the opposite direction (toward the wall).(see fig I or J) 2.22.22.22.22.2 Ceiling or shelf mounting orientation Now, position the clamp assembly on the wall, ceiling or shelf at the mounting location you have selected. Using the clamp plate as a template, accurately mark the two hole locations with a pencil. Remove the clamp plate before drilling holes. STEP 3:STEP 3:STEP 3:STEP 3:STEP 3: PREPARING THE MOUNTING SURFACE AND ATTACHING THEPREPARING THE MOUNTING SURFACE AND ATTACHING THEPREPARING THE MOUNTING SURFACE AND ATTACHING THEPREPARING THE MOUNTING SURFACE AND ATTACHING THEPREPARING THE MOUNTING SURFACE AND ATTACHING THE CLAMP ASSEMBLCLAMP ASSE...