Votos - , Puntuación media:
(
)
)
Fabricar: Vidikron
Tamaño del archivo: 3.85 mb
Nombre del archivo: b9bccf3c-1521-414c-8a3f-9a71c01198d9.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
This feature removes all red and green color information from the image (simulating a blue filter), and is useful for color-calibrating the projector or other video components. Save Settings: When you have finished making your adjustments, select Save Settings to store the settings for the current input in the “Custom 1” memory location. Load Saved Settings: To recall stored custom image quality settings, select Load Saved Settings and choose “Custom 1,” “ISF Night” or “ISF Day.” . Projector Status To load default settings, configure the sleep timer or adjust the lamp, select Projector Status from the Main Menu and press ENTER. Default: To restore the default image settings for the current input source ONLY, press the or button to highlight “Load,” then press ENTER. Sleep Timer: The Sleep Timer automatically puts the projector into standby mode after the amount of time you specify here. (A warning appears on-screen one minute before this is to occur.) Use the or button to set the timer for anywhere from 10 to 180 minutes (three hours), in 10-minute increments. To disable the Sleep Timer, set it to 0. Lamp Power: Select Lamp Power from the Projector Status Menu to adjust the lamp output level. You can choose to run the lamp as bright as possible (250W; this is the default setting) or you can choose the lower (200W) setting. Generally, lower lamp output can prolong the life of the lamp, but decreases brightness. Lamp Hours: Lamp Hours indicates how long the currently-installed lamp has been in service. (This part of the menu is read-only.) Installation To access the Installation adjustments, press MENU, then press the or button to highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears. Press EXIT to return to the previous menu or press MENU to close all menus. Note When you change a setting in the Installation menu, the change takes effect immediately; you do not need to press ENTER afterwards. (Press EXIT to return to the previous menu or MENU to exit.) Language: Press the or button to select from the available languages (English, French, Spanish, German and Italian). Picture Configuration: Press the or button to change the orientation of the projected image. The Vision 70 can be installed on a ceiling or in a rear-screen configuration with one or more mirrors. There are four settings: Floor Front, Ceiling Front, Floor Rear and Ceiling Rear. Keystone: To correct distortion resulting from the angle of projection, select Keystone and use the or button to make the image rectangular. Tip Vidikron recommends that the keystone feature not be used unless absolutely necessary, as it may cause artifacts in the image. OSD Position: To adjust the horizontal and vertical position of the OSD, select OSD Position and press ENTER. Then, press the or button to select Horizontal or Vertical and use the or button to adjust. OSD Timer: Use the or button to set the OSD Timer. This timer controls how long the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in 3-second increments. When you set the OSD Timer to 0, the menus remain on-screen until you hide them by pressing MENU. PIP/PBP Setup: Select PIP/PBP Setup from the Installation menu to change the PIP/PBP settings. •PIP/PBP Enable: Press the or button to select PIP/PBP Enable, then press ENTER. Press the or button to select Off or On, then press ENTER. •PIP Set Up: Press the or button to select PIP Set Up, then press ENTER. Press the or button to select PIP Off, Graphic in Video or Video in Graphic, then press ENTER. •PBP Set Up: Press the or button arrows to select PBP Set Up, then press ENTER. Press the or button to select PBP Off, Graphic by Video or Video by Graphic, then press ENTER. Background Color: Press the or button to select the image Background Color (grey, blue or white). The Background Color appears when no incoming signal is present. . Service To access advanced projector settings, use the up- or down-arrow keys to select Service from the Main Menu and press ENTER. Use the number buttons on the remote to enter the Service menu passcode when prompted and press ENTER again. Then, press MENU on the remote control. Note You only need to enter the Service menu passcode the first time you select that menu after turning on the projector. White Balance: To remove any trace of color from the white areas of the projected image, choose White Balance from the Service menu and press ENTER. •Gamma: “Gamma” is a global setting that determines how gray shades are displayed between minimum input (black) and maximum input (white) for all signals. A good gamma setting helps to optimize blacks and whites while ensuring smooth transitions for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast” controls, the overall tone of your images can be lightened or darkened without changing the extremes and all images will be more vibrant while still showing good detail in dark areas. In all but the ...